Page 3 - iii; Special notes on LCD monitors; Safety instructions; Cleaning your monitor; Connecting/disconnecting the device
iii Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears. • You may f...
Page 4 - iv; Accessibility; Warnings; Using electrical power
iv Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To protect yo...
Page 5 - Product servicing
v ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. • Do not overload a power outlet, strip or receptacle by plugging in ...
Page 6 - Potentially explosive environments; Additional safety information
vi Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Potentially explosive environments Switch o...
Page 7 - vii; Disposal instructions
vii Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit LCD pixel ...
Page 8 - viii; Tips and information for comfortable use; Finding your comfort zone
viii This product has been shipped enabled for power management: • Activate display’s Sleep mode within 15 minutes of user inactivity. • Activate computer’s Sleep mode within 30 minutes of user inactivity. • Wake the computer from Sleep mode by pushing the power button. Tips and information for comf...
Page 9 - ix; Taking care of your vision
ix Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain.Eyes • R...
Page 10 - Declaration of Conformity
xxxxxx B226HQL B226HQL ; Acer Incorporated 8F, 88, Sec. 1, Xintai 5th Rd., Xizhi New Taipei City 221, Taiwan Declaration of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan Contact Person: Mr. RU Jan, e-mail:[email protected] And, Acer Italy s.r.l Via...
Page 11 - Monitor; 33 West San Carlos St.; Acer America Corporation
Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference ...
Page 13 - Unpacking
1 Unpacking Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. LCD monitor Quick start guide D-sub cable (Option) DVI cable (Option) AC power cord Audio Cable (Option) (Option) DP ...
Page 18 - Connector pin assignment
6 Connector pin assignment 15-pin color display signal cable PIN No. Description PIN No. Description 1 Red 9 +5 V 2 Green 10 Logic ground 3 Blue 11 Monitor ground 4 Monitor ground 12 DDC-serial data 5 DDC-return 13 H-sync 6 R-ground 14 V-sync 7 G-ground 15 DDC-serial clock 8 B-ground 1 5 6 10 11 15
Page 20 - Standard timing table
8 Standard timing table 1 VGA 640×480 60 Hz 2 MAC 640×480 66.66 Hz 3 VESA 720×400 70 Hz 4 SVGA 800×600 56 Hz 5 SVGA 800×600 60 Hz 6 XGA 1024×768 60 Hz 7 XGA 1024×768 70 Hz 8 VESA 1152×864 75 Hz 9 SXGA 1280×1024 60 Hz 10 VESA 1280×720 60 Hz 11 WXGA 1280×800 60 Hz 12 WXGA+ 1440×900 60 Hz 13 WXGA+ 1680...
Page 21 - Installation; Steps
9 Installation To install the monitor on your host system, please follow the steps below: Steps 1 Connect the video cablea Make sure both the monitor and computer are switched off. b Connect the VGA video cable to the computer. c Connect the digital cable (only for dual-input models).(1) Make sure b...
Page 22 - U S E R C O N T R O L S; To turn the monitor ON or OFF.; Using the Shortcut Menu; AUTO; OSD functions; Press this botton to activate the OSD menu.; INPUT; Input Key; seconds for the image to appear.
EN-13 U S E R C O N T R O L S Power Switch / Power LED: To turn the monitor ON or OFF. Lights up to indicate the power is turned ON. Using the Shortcut Menu Press the function button to open the shortcut menu. The shortcut menu lets youquickly select the most commonly accessed settings. Empowering: ...
Page 23 - Step 1: Press “ “ Key to open the Acer eColor Management OSD and; F ea t u r e s an d Be n e f i t s; Step 3: Press “ AUTO “ Key to confirm the mode and exit the eColor menu.; Adjusts the settings to reduce power
EN-14 M a in M e n u ic o n S u b M e n u ico n Su b Me n u ite m D e scrip tio n N/A User mode User defined. Settings can be fine-tuned to suit any situation N/A N/A Standard mode D e f a u lt S e t t i n g . R e f l e c t s n a t i v e d is p la y capability N/A Grahpic mode Enhances colors and em...
Page 24 - A d j u s t i n g the OSD set t i n g s; A d j u s t i n g the p i c t u r e q u a l i t y
EN-15 A d j u s t i n g the OSD set t i n g s -------------------------------------------------------------------- Note: The following content is for general reference only. Actualproduct specifications may vary. The OSD can be used for adjusting the settings of your LCD Monitor.Press the MENU key t...
Page 27 - Information
EN-18 Pr o d u c t informa ti o n 1 Press the MENU key to bring up the OSD.2 Using the / keys, select Information from the OSD. Then the basic information of LCD monitor will show up for current input. 1920 x 1080 Information H:65KHz V:60Hz VGA Input S/N:ETL5309 1326350380B3742
Page 28 - Troubleshooting; VGA mode
1 5 Eng lis h Troubleshooting Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. VGA mode Problem LED status Remedy No picture visible Blue Using the OSD, adjust brightness and contrast to maximum or reset to their ...
Page 29 - English; DVI mode
1 6 English DVI mode Problem LED status Remedy No picture visible Blue Using the OSD, adjust brightness and contrast to maximum or reset to their default settings. Off Check the power switch. Check if the AC power cord is properly connected to the monitor. Amber Check if the video signal cable is pr...
