Acer AL1951 - Manuals - manualsarea.com

Page 3 - PRECAUTIONS; The monitor should be operated only from the type of power source

2 PRECAUTIONS z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Us...

Page 5 - a b; Place four screws into the holes as shown and tighten

4 POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the AC-power cord into...

Page 7 - ADJUSTING THE VIEWING ANGLE; You can adjust the angle of the monitor from -5

6 • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. Figure 2 NOTES • Do not touch the LCD screen when you change the angle. It...

Page 8 - OPERATING INSTRUCTIONS; GENERAL INSTRUCTIONS; The power cord should be connected.

7 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be con...

Page 9 - off; NOTES

8 FRONT PANEL CONTROL • Power Button: Press this button to turn the monitor ON or OFF, And display the monitor’s state. • Power Indicator: Blue — Power On mode. Orange — Power off . • MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit ...

Page 10 - Model; HOW TO ADJUST A SETTING

9 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function. 5. To exit and save, select the exit function. I...

Page 11 - ADJUSTING THE PICTURE

10 III. Dual-Input Model, Digital Signal Input ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Icon Sub Menu Icon Sub Menu Item Description Contrast Adjusts the contrast between the foreground and background of the screen image. Brightness Adjusts the background brightness...

Page 13 - PLUG AND PLAY; The DDC2B is a bidirectional data; USING THE RIGHT POWER CORD :

12 PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capab...

Page 16 - ERROR MESSAGE & POSSIBLE SOLUTION

15 ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. 2. Check the signal -cable connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display...

Page 17 - Input

16 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 4 8 cm(1 9 ") Pixel pitch 0.2 9 4mm( H )x 0.2 9 4mm( V ) Brightness 300 cd/m 2 (Typical) Contrast 70 0:1(Typical) Viewable angle 1 5 0 ° (H) 1 35 ° (V) Response time 8 ms R,G,B Analog Interface Video Digital interface(Only Du...

Page 19 - Preset Display Modes

18 Preset Display Modes VIDEO MODE RESOLUTION HORIZONTAL FREQUENCY(kHz) VERTICAL FREQUENCY(Hz) 640 × 480 31.469 59.940 VGA 640 × 480 37.500 75.000 800 × 600 37.879 60.317 SVGA 800 × 600 46.875 75.000 1024 × 768 48.363 60.004 1024 × 768 56.476 70.069 XGA 1024 × 768 60.023 75.029 1280 × 1024 64.000 60...

Page 20 - CONNECTOR PIN ASSIGNMENT

19 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data 5. DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground (Dual-In...