Page 2 - Revision History
II Revision History Please refer to the table below for the updates made on PD 7 26 & PH730 service guide. Date Chapter Updates
Page 3 - Copyright
III Copyright Copyright © 200 5 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optic...
Page 4 - Conventions
IV Conventions The following conventions are used in this manual: Screen messages Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific acti...
Page 5 - Preface
V Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market r...
Page 6 - Table of Contents
Table of Contents Chapter 1 System Introduction 1 Technical Specification 1 Product Overview 3 System Block Diagram 7 Chapter 2 Firmware Upgrade 8 Equipment Needed 8 Installation Procedure 9 Firmware Upgrade Procedure 13 EDID Upgrade 16 EDID Introduction 16 Equipment Needed 16 Setup Procedure 17 EDID...
Page 7 - System Introduction - PD726; Technical Specification; Item; Chapter 1
1 Chapter 1 System Introduction - PD726 Technical Specification Item Description Dimensions (LxWxH) 350 x 282 x 118.75 mm Weight Approx. 7.7 lbs (3.5 Kg) Tilt Angle 6 degree with elevator mechanism Keystone correction +/-16 degree (32 degree) Lamp Door Projection Lamp power supply shut off automatica...
Page 8 - System Introduction - PH730
Chapter 1 2 System Introduction - PH730 Technical Specification Item Description Dimensions (LxWxH) 350 x 282 x 118.75 mm Weight Approx. 7.7 lbs (3.5 Kg) Tilt Angle 6 degree with elevator mechanism Keystone correction +/- 6 Degree Lamp Door Projection Lamp power supply shut off automatically when doo...
Page 9 - Product Overview; Main Unit
3 Chapter 1 Product Overview Main Unit Item Description 1 Focus Ring / Zoom Ring 2 Zoom Lens 3 Elevator Button 4 Remote Control Receiver 5 Lens Cap Switch 6 Elevator Foot 7 Connection Ports 8 Power Socket 9 Control Panel 10 Detachable cable holder
Page 10 - Control Panel
Chapter 1 4 Control Panel Item Description 1 Temp Indicator LED 2 Lamp Indicator LED 3 Power and Indicator LED (Power LED) 4 Source 5 Resync 6 Empowering Key 7 Menu 8 Back 9 Four Directional Select Keys (Keystone)
Page 11 - Connection Ports
5 Chapter 1 Connection Ports Item Description 1 USB Connector 2 HDMI Connector 3 DVI Input Connector 4 VGA Input Connector (PC Analog Signal) 5 Component Video Input Connector 6 S-Video Input Connector 7 RS232 Connector 8 Kensington TM Lock Port 9 Power Socket 10 VGA Output Connector (Monitor Loop-t...
Page 12 - Connecting the Projector
Chapter 1 6 Item Description 1 Power Cord 2 VGA Cable 3 Composite Video Cable 4 USB Cable 5 HDMI Cable (Optional Accessory) 6 S-Video Cable 7 Audio Cable Jack / Jack or Audio Cable Jack / RCA 8 DVI Cable (Optional Accessory) 9 3 RCA Component Cable 10 RS232 Cable (Optional Accessory) Connecting the ...
Page 14 - Chapter 2; Firmware Upgrade; Equipment Needed
Chapter2 8 Chapter 2 Firmware Upgrade Item Photo Item Photo Projector (PD726 & PH730) USB Cable Power Cord PC or Lap-top Equipment Needed Software : (DDP 3020- USB) - DLP Composer Lite (6.0) - Firmware (PD726 & PH730) Hardware :
Page 15 - Step; Execute; Installation Procedure; DLP Composer Lite Setup Procedure
9 Chapter 2 No Step Procedure Photo 1 Execute FW pro- gram Choose “DLP Composer Lite v6.0 Setup” program. 2 Next Click “Next” button. 3 Next 1. Reading the “License Agreement” rules. 2. Choose “I accept and agree to be bound by all the terms and conditions of this License Agreement” icon.3. Click “N...
Page 16 - Next
Chapter2 10 No Step Procedure Photo 5 Next 1. Choose “All” icon.2. Click “Next” button. 6 Next Click “Next” button. 7 Process- ing The program is execut-ing “Initializing” status.
Page 17 - USB Driver Upgrade Procedure
11 Chapter 2 No Step Procedure Photo 1 Set-up 1. Hold on “Menu” button and plug in Power Cord while holding on “Menu”.2. Wait for about 5 secs.3. Once Power, Lamp, Temp LED lights up, then, plug in USB Cable into the Projector. (Note: The system fan will operate in full speed. The light will not fun...
Page 18 - Update
Chapter2 12 No Step Procedure Photo 4 Update Success- fully In 1 minute, click “OK”. The USB driver is up-dated successfully. 5 Device Manager 1. Right click “My computer” on the desktop. 2. Select “Properties” on the popup menu to launch the “System Properties” window.3. Choose “Hardware” and then ...
Page 19 - Firmware Upgrade Procedure
13 Chapter 2 Firmware Upgrade Procedure 1 2 No Step Procedure Photo 1 Set-up 1. Hold on “Menu” button and plug in Power Cord while holding on “Menu”.2. Wait for about 5 secs.3. Once Power, Lamp, Temp LED lights up, plug in USB Cable into the Projector. (Note: The system fan will be operated in full ...
Page 21 - ing; Check
15 Chapter 2 No Step Procedure Photo 9 Proceed- ing Proceeding Picture 10 1. When Firmware Upgrade Process is finished, the LED power flashs.2. Unplug USB Cable and Power Cord. Re-plug in Power Cable. 11 Check Firmware Restart the unit and enter the Service Mode to check the Firmware Version. (For ent...
Page 22 - EDID Upgrade
Chapter2 16 Item Photo Item Photo RS-232 Cable(F - M) Power Adapter for Fixture DVI Cable Generic Fixture VGA Cable Power Cord EDID Upgrade Equipment Needed Software: - EDID Software (Generic V0.51) - EDID Table (*.ini) -- PD726 or PH730 Hardware: - V3 Fixture for EDID Key-in (Fixture: JP3 must be c...
Page 23 - Setup Procedure
17 Chapter 2 Item Photo Item Photo PC One additional monitor (for checking the pro- gram execution) Projector(PD726 / PH730) DVI-HDMI Connector No Step Procedure Photo 1 Execute EDID Program. Click on “EDID” to ex-ecute EDID Program. 2 Choose Model 1. In the Port Selection Bar, please choose the Por...
Page 27 - Mechanical Disassembly & Reassembly; place and separate them according to their category.; Chapter 3; General Information; Before You Begin; Turn off the power of the system and all the peripherals.
21 Chapter 3 Mechanical Disassembly & Reassembly This section provides disassembly & Reassembly procedures for PD726 & PH730 DMD Projector. Before you begin any of these procedures, be sure to turn off the power, computer system, and other attached devices; then disconnect the power cabl...
Page 28 - Procedure; Loosen 2 tenons to remove; Remove Lamp Module; Mechanical Disassembly Procedure
Chapter 3 22 No Procedure Photo 1 Loosen 2 tenons to remove the Lamp Cover. 2 Unscrew 3 screws to remove the Lamp Module. 1. Remove Lamp Module Mechanical Disassembly Procedure
Page 29 - Remove and disassemble Top Cover Module
23 Chapter 3 No Procedure Photo 1 Unscrew 6 screws in the Bottom Cover, then, unplug 1 IR Receiver wire and 1 FPC connector to remove Top Cover Module. 2 Remove Keypad Board: (1) Unscrew 4 screw and unplug 1 FPC to remove the Keypad Board. (2) Separate all the keypad components. 3 IR Receiver: Tear ...
Page 31 - Unscrew 5 screws, unplug 10
25 Chapter 3 3. Remove Main Board & Audio Board No Procedure Photo 1 Unscrew 5 screws, unplug 10 connectors and 1 connector in the Bottom; then, unscrew 6 hex screws to remove the Main Board & Audio Board.
Page 32 - Remove the IO Cover / Side
Chapter 3 26 No Procedure Photo 1 Remove the IO Cover / Side Covers with Speakers directly. (Right Cover & Left Cover) 2 Remove LVPS: (1) Unscrew 6 screws and unplug 2 wires (2) Unplug 3 connectors to remove the LVPS. 4. Remove IO Cover and Side Covers (Speakers) / LVPS
Page 33 - remove the Thermal Switch.
27 Chapter 3 5. Remove Thermal Switch / Light Cut / Air Duct No Procedure Photo 1 (1) Unscrew 1 screw to remove the Thermal Switch. (2) Unscrew 5 screws to remove the Light Cut. 2 Unscrew 1 screw to remove the Air Duct.
Page 34 - Remove Lamp Driver:
Chapter 3 28 6. Remove Lamp Driver / Fan No Procedure Photo 1 Remove Lamp Driver: (1) Unscrew 4 screws (2) Unscrew 2 screws and unplug 3 connectors to remove the Lamp Driver. 2 Remove Fan Module: (1) Unscrew 2 screws to remove the Fan Module. (2) Unscrew 4 screws to separate the Fan Module.
Page 35 - Remove Engine Module; remove the Engine Module.
29 Chapter 3 7. Remove Engine Module No Procedure Photo 1 (1) Unscrew 4 screws to remove the Engine Module. (2) Take off the Mylar on the DMD Board directly. 2 Unscrew 5 screws to remove the Mylar. 3 (1) Unscrew 1 screw to remove the Color Wheel. (2) Unscrew 1 screw to remove the Photosensor Board. ...
Page 36 - separate the DMD Board and
Chapter 3 30 No Procedure Photo 4 (1) Unscrew 4 screws to remove the Heatsink. (2) Unscrew 4 screws to separate the DMD Board and disassemble the components. 5 (1) Unscrew 3 screws to remove the Focus Ring. (2) Take the Zoom Ring off directly.
Page 37 - remove the Front IR Receiver; Remove Bottom Cover
31 Chapter 3 No Procedure Photo 1 (1) Unscrew 4 screws to remove the Elevator (Left). (2) Unscrew 4 screws to remove the Elevator (Right). (3) Tear off the Mylar and remove the Front IR Receiver directly. (4) Unscrew 3 screws to remove the Fan 1. (5) Unscrew 2 screws to remove the Fan 2. (6) Unscrew...
Page 38 - Assemble Bottom Cover; Mechanical Reassembly Procedure; Screw 9 hex spacers to the
Chapter 3 32 1. Assemble Bottom Cover Mechanical Reassembly Procedure No Procedure Photo 1 Screw 9 hex spacers to the Bottom Cover. 2 (1) Screw 4 screws to assemble the Elevator (Left). (2) Screw 4 screws to assemble the Elevator (Right). (3) Assemble the Front IR Receiver with the Mylar directly. (...
Page 39 - Assemble Engine Module
33 Chapter 3 No Procedure Photo 1 (1) Assemble the Zoom Ring directly. (2) Screw 3 screws to assemble the Focus Ring. 2 (1) Assemble all the components and screw 4 screws to assemble the DMD Board. (2) Screw 4 screws to assemble the Heatsink. 3 (1) Screw 1 screw to assemble the Photosensor Board wit...
Page 40 - Unscrew 5 screws to remove
Chapter 3 34 No Procedure Photo 4 Unscrew 5 screws to remove the Mylar. 5 (1) Unscrew 4 screws to remove the Engine Module. (2) Take off the Mylar on the DMD Board directly.
Page 41 - Assemble Fan Module:
35 Chapter 3 3. Assemble Fan / Lamp Driver No Procedure Photo 1 Assemble Fan Module: (1) Screw 4 screws to assemble the Fan Module components. (2) Screw 2 screws to assemble the Fan Module. 2 Assemble Lamp Driver: (1) Plug in 3 connectors and screw 2 screws. (2) Screw 4 screws to assemble the Lamp D...
Page 42 - Screw 1 screw to assemble
Chapter 3 36 4. Assemble Air Duct / Light Cut / Thermal Switch No Procedure Photo 1 Screw 1 screw to assemble the Air Duct. 2 (1) Screw 5 screws to assemble the Light Cut. (1) Screw 1 screw to assemble the Thermal Switch.
Page 43 - screws to assemble the
37 Chapter 3 No Procedure Photo 2 Assemble LVPS: (1) Plug in 3 connectors. (2) Plug in 2 wires and screw 6 screws to assemble the LVPS. 1 Assemble the IO Cover / Side Covers with Speakers directly. (Right Cover & Left Cover) 5. Assemble LVPS / IO Cover & Side Covers (Speakers)
Page 44 - Screw 6 hex screws in the
Chapter 3 38 6. Assemble Main Board & Audio Board No Procedure Photo 1 Screw 6 hex screws in the Bottom Cover; then, plug in 10 connectors and 1 connector in the Bottom and screw 5 screws to assemble the Main Board & Audio Board.
Page 45 - Assemble Top Cover Module
39 Chapter 3 No Procedure Photo 1 Assemble Assy Manual Lens Cap Module: (1) Fasten 6 tenons and screw 1 screw to assemble the Lens Cap. (2) Screw 2 screws in the front & 2 screws in the back to assemble the Lens Cap. (3) Screw 4 screws to assemble the Lens Cap Module. 2 IR Receiver: Put on the m...
Page 46 - Assemble Keypad Board:
Chapter 3 40 No Procedure Photo 3 Assemble Keypad Board: (1) Assemble all the keypad components. (2) Plug in 1 FPCU and screw 4 screw to assemble the Keypad Board. 4 Plug in 1 IR Receiver wire and 1 FPC connector; then, screw 6 screws in the Bottom Cover to assemble the Top Cover Module.
Page 47 - Screw 3 screws to assemble; Assemble Lamp Module
41 Chapter 3 No Procedure Photo 1 Screw 3 screws to assemble the Lamp Module. 2 Fasten 2 tenons to assemble the Lamp Cover. 8. Assemble Lamp Module
Page 48 - Troubleshooting; Chapter 4; - PC or Pattern Generator; LED Lighting Message
Chapter 4 42 Troubleshooting Chapter 4 Equipment Needed - PC or Pattern Generator - DVD Player (Video, S-Video, Audio) - Quantum Data 802B or CHROMA 2327 LED Lighting Message Message Lamp LED Red Temp LED Red Power LED orange Power Plug Flash ON to OFF 100ms Flash ON to OFF 100ms Flash ON to OFF 100...
Page 49 - Main Procedure; Symptom
43 Chapter 4 Main Procedure No Symptom Procedure 1 No Power - Ensure the Power Cord and AC Power Outlet are securely connected- Check Lamp Cover and Interrupt Switch- Ensure all connectors are securely connected and aren’t broken- Check DC-DC- Check Ballast- Check Main Board 2 Auto Shut Down - Check...
Page 51 - Chapter 5; Exploded Overview
Chapter 5 48 Chapter 5 Exploded Overview EXPLODED OVERVIEW (D.C PD726)
Page 52 - Exploded Parts List; Note: Please refer to RSPL for updated Part Number.
49 Chapter 5 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 70.83N01G001 ASSY ENGINE MODULE PD726 2 70.83N07G001 ASSY LAMP CHANGER MODULE PD726 3 70.83N09G001 ASSY TOP COVER MODULE PD726 4 70.83N10G001 ASSY BOTTOM HOUSING MODULE PD726 5 51.83N1...
Page 53 - ASSY ENGINE MODULE PD726
Chapter 5 50 ASSY ENGINE MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 70.83N04G001 ASSY OPTICAL ENGINE MODULE PD726 2 70.83N02G001 ASSY ENGINE BASE MODULE PD726 3 85.1A126G080 SCREW PAN MECH M2.6*8 Ni
Page 54 - ASSY ENGINE BASE MODULE PD726
Page 56 - ASSY COLOR WHEEL MODULE PD726
53 Chapter 5 ASSY COLOR WHEEL MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 23.83N19G001 COLOR WHEEL X48mm R92/G83/W110/B75 SLEEVE BEARING CW; YO 2 52.89606G001 COLOR WHEEL RUBBER EP759/PD726 3 61.89511G001 COLOR WHEEL SCREW 4100M...
Page 59 - ASSY LAMP CHANGER MODULE PD726
Chapter 5 56 ASSY LAMP CHANGER MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 23.89610G002 BOROFLOAT UV-IR SQUARE t2.75mm 2 23.83N15G001 OSRAM LAMP E21.8 1.3mm ARC 300W G2 3 61.89633G001 LAMP MECH GREEN EP759/PD726 4 51.89621G012 L...
Page 60 - ASSY TOP COVER MODULE PD726
57 Chapter 5 ASSY TOP COVER MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 75.83N03G001 ASSY TOP COVER PD726 2 51.83N03G001 KEYPAD MAIN BUTTON PC PD726 3 51.83N04G001 KEYPAD MIDDLE BUTTON PC PD726 4 80.83N04G001 PCBA KEY BOARD ASSY...
Page 61 - ASSY BOTTOM HOUSING MODULE PD726
Page 63 - ASSY BOTTOM COVER MODULE PD726
Chapter 5 60 ASSY BOTTOM COVER MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 75.83N04G001 ASSY BOTTOM COVER PD726 2 70.83N18G001 ASSY LEFT COVER MODULE PD726 3 70.83N19G001 ASSY RIGHT COVER MODULE PD726 4 52.89610G001 STEAMTIGHT N...
Page 64 - ASSY LVPS MODULE PD726
61 Chapter 5 ASSY LVPS MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 42.89611G001 W.A. 3P #20 250mm LAMP DRIVER TO LVPS EP759/PD726 2 75.82B28G001 BUY ASSY BRACKET LVPS HOLDER 5100MP 3 61.82K16G001 SCREW M4 AC GROUNDING 4 75.83N10...
Page 65 - ASSY LAMP DRIVER MODULE PD726
Chapter 5 62 ASSY LAMP DRIVER MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 42.89608G001 W.A. 5P #28 140mm LAMP DRIVER TO MAIN BD EP910 2 51.89639G001 LAMP DRIVER EMI MYLAR EP759/PD726 3 75.80L01G003 ASSY OSRAM LAMP DRIVER 300W TY...
Page 68 - ASSY INTERRUPT SWITCH MODULE PD726
65 Chapter 5 ASSY INTERRUPT SWITCH MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 43.889601G001 INTERRUPT SWITCH LC-8306 EP759/PD726 2 51.89623G001 INTERRUPT S/W HOLDER TOP PC+ABS C6200 EP759/PD726 3 51.89624G001 INTERRUPT S/W HOLD...
Page 70 - ASSY LEFT COVER MODULE PD726
67 Chapter 5 ASSY LEFT COVER MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 75.83N07G001 ASSY LEFT COVER PD726 2 52.89608G001 SPEAKER SPONGE CR 2t EP759/PD726 3 49.83N03G001 SPEAKER 8ohm 3W PD726/PH730 4 85.1A123G060 SCREW PAN MECH...
Page 71 - ASSY RIGHT COVER MODULE PD726
Chapter 5 68 ASSY RIGHT COVER MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 75.83N08G001 ASSY RIGHT COVER PD726 2 52.89608G001 SPEAKER SPONGE CR 2t EP759/PD726 3 49.83N03G001 SPEAKER 8ohm 3W PD726/PH730 4 85.1A123G060 SCREW PAN ME...
Page 72 - ASSY ROD MODULE PD726
69 Chapter 5 ASSY ROD MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 23.89617G002 HOLLOW ROD 6.2mm*4.6mm*31.3mm(t1.1mm) 2 61.89620G001 ROD HOLDER SUS301 0.2t EP759/PD726
Page 73 - ASSY RELAY LENS MODULE PD726
Chapter 5 70 ASSY RELAY LENS MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 23.89606G001 ASPHERIC RELAY LENS GREEN DESIGN EP759 2 51.89625G001 RELAY HOLDER PPS+40%GF EP759/PD726 3 61.89612G001 RELAY SPRING PLATE SUS301 0.4t EP759/P...
Page 74 - MANUAL LENS CAP MODULE PD726
71 Chapter 5 MANUAL LENS CAP MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 51.83N08G001 ADJUST BUTTON COVER PC MN-3600H PD726 2 51.83N07G001 LENSCAP ADJUST BUTTON PC MN-3600H PD726 3 61.83N02G001 MANUAL LENS CAP AL-HAIRLINE PD726 ...
Page 75 - ASSY MAIN-BD MODULE PD726
Chapter 5 72 ASSY MAIN-BD MODULE PD726 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 75.83N01G001 ASSY MAIN BOARD MODULE PD726 2 51.83N17G001 BACK COVER PC MN-3600H PD726 3 85.1A123G060 SCREW PAN MECH M3*6 NI 4 51.83N27G001 BACK I/O SHEET NO W...
Page 76 - EXPLODED OVERVIEW D.C PH730
Page 78 - ASSY ENGINE MODULE PH730
75 Chapter 5 ASSY ENGINE MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 70.85A05G001 ASSY OPTICAL ENGINE PH730 2 70.85A02G001 ASSY ENGINE BASE MODULE PH730 3 85.1A126G080 SCREW PAN MECH M2.6*8 Ni
Page 79 - ASSY ENGINE BASE MODULE PH730
Page 81 - ASSY COLOR WHEEL MODULE PH730
Chapter 5 78 ASSY COLOR WHEEL MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 23.83N19G001 COLOR WHEEL X48mm R92/G83/W110/B75 SLEEVE BEARING CW; YO 2 52.89606G001 COLOR WHEEL RUBBER EP759/PD726 3 61.89511G001 COLOR WHEEL SCREW 4100M...
Page 82 - ASSY ROD MODULE PH730
79 Chapter 5 ASSY ROD MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 23.89617G002 HOLLOW ROD 6.2mm*4.6mm*31.3mm(t1.1mm) 2 61.85A02G001 ROD HOLDER SUS301 0.2t PH730
Page 83 - ASSY OPTICAL ENGINE MODULE PH730
Page 85 - ASSY LAMP CHANGER MODULE PH730
Chapter 5 82 ASSY LAMP CHANGER MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 23.89610G002 BOROFLOAT UV-IR SQUARE t2.75mm 2 23.83M15G001 OSRAM E20.5 LAMP 250W 3 61.00018G002 LLOCK SCREW PAN MECH M3*8.5-3.5 BLACK 4 51.85A01G001 E20d...
Page 86 - ASSY TOP COVER MODULE PH730
83 Chapter 5 ASSY TOP COVER MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 75.83N03G001 ASSY TOP COVER PD726 2 51.83N03G001 KEYPAD MAIN BUTTON PC PD726 3 51.83N04G001 KEYPAD MIDDLE BUTTON PC PD726 4 80.83N04G001 PCBA KEY BOARD ASSY...
Page 87 - ASSY LAMP DRIVER MODULE PH730
Chapter 5 84 ASSY LAMP DRIVER MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 42.89608G001 W.A. 5P #28 140mm LAMP DRIVER TO MAIN BD EP910 2 75.83M02G001 ASSY OSRAM 03 LAMPDRIVER 260W A4544210027 3 76.89601G011 ASSY LAMP DRIVER(OSRAM...
Page 88 - ASSY BOTTOM HOUSING MODULE PH730
Page 90 - MANUAL LENS CAP MODULE PH730
87 Chapter 5 MANUAL LENS CAP MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 51.83N08G001 ADJUST BUTTON COVER PC MN-3600H PD726 2 51.83N07G001 LENSCAP ADJUST BUTTON PC MN-3600H PD726 3 61.83N02G001 MANUAL LENS CAP AL-HAIRLINE PD726 ...
Page 91 - ASSY MAIN-BD MODULE PH730
Chapter 5 88 ASSY MAIN-BD MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 75.85A01G001 ASSY MAIN MODULE PH730 2 51.83N17G001 BACK COVER PC MN-3600H PD726 3 85.1A123G060 SCREW PAN MECH M3*6 NI 4 51.83N27G001 BACK I/O SHEET NO WIRELES...
Page 92 - ASSY RIGHT COVER MODULE PH730
89 Chapter 5 ASSY RIGHT COVER MODULE PH730 Exploded Parts List Note: Please refer to RSPL for updated Part Number. Item Part Number Description 1 75.85A04G001 ASSY RIGHT COVER PH730 2 52.89608G001 SPEAKER SPONGE CR 2t EP759/PD726 3 49.83N03G001 SPEAKER 8ohm 3W PD726/PH730 4 85.1A123G060 SCREW PAN ME...
Page 94 - Appendix; Serial Number Definition System; I. Serial Number System Definition; The coding rule of the Bar Code:; number Started from “0001”.
91 Appendix Appendix Serial Number Definition System I. Serial Number System Definition Serial No. (Acer Barcode rule), 22 digits (Barcode Type: Code 128) PPPPPPPPPPWWWSSSSSMMEEE The coding rule of the Bar Code: (1) PPPPPPPPPP (10 digitals) : Part Number excluded “dot” Ex: EY.J1401.001. (2) WWW (3 dig...
Page 95 - Vendor Code; II. PCBA Code Definition; PCBA Code for Projector; A B XXXXXXXXXX C XXX; EEEE
Appendix 92 : ID : Vendor Code : P/N : Revision : Date Code : S/N II. PCBA Code Definition PCBA Code for Projector A B XXXXXXXXXX C XXX EEEE 1 2 3 4 5 6 1 2 3 4 5 6 C: M/B B: DMD/ B
