Accton 16 - Manuals - manualsarea.com

Page 2 - Thin Ethernet; ) terminator to the open end of the “T” connector. If the BNC; Thick Ethernet

EtherHub-16 Quick Start Guide 2 2. If you are making a connection to an end-node device (e.g., a PC or server), be sure that it has a properly installed 10BASE-T network interface card. Attach one end of a straight-throughtwisted-pair cable to an standard port (Port 1 ~ 16MDI-X ) on the hub and the ...

Page 3 - EtherHub-16 Quick Start Guide; Providing Power to the Hub; and the other end into a power outlet.; Power; on the front panel to see if it is on. The unit automatically; System Configuration

EtherHub-16 Quick Start Guide 3 Providing Power to the Hub 1. Power on the hub by plugging the power cord into the power socket at the rear of the hub, and the other end into a power outlet. 2. Check the LED marked Power on the front panel to see if it is on. The unit automatically selects a setting...

Page 4 - Hardware Description; terminators to the T-type connector on the BNC port.

EtherHub-16 Quick Start Guide 4 Hardware Description RJ-45 Ports This hub has 16 RJ-45 ports that can be used to connect end-node devices (e.g., workstations, fileservers, or printers). Be sure you have an Ethernet network interface card installed in the deviceto be connected to the hub. Then connec...

Page 5 - LED; Troubleshooting; Workstation’s network adapter, cable or hub port is defective.

EtherHub-16 Quick Start Guide 5 AUI Port This hub has two built-in AUI transceivers (i.e., AUI1 and AUI2) on the rear panel for connectionusing thick Ethernet cable (10BASE5) or fiber optic Ethernet cable (10BASE-F). To use eitherAUI port, set the DIP switches to the correct positions and described ...

Page 6 - Jabber indicator lights up.; Specifications

EtherHub-16 Quick Start Guide 6 Symptom: Jabber indicator lights up. Causes: Frame received on this port exceeds length threshold for Jabber Lockup Protection. Solution: If jabber lockup has occurred, it will be automatically re-enabled when the problemis corrected or the port receives a valid data ...

Page 7 - EMI Warning; FCC Class A Certification; You may use unshielded or shielded twisted-pair (100; electrostatic discharge whenever handling this equipment.

EtherHub-16 Quick Start Guide 7 EMI Warning FCC Class A Certification This device complies with Part 15 of the FCC Rules. Operation is subject to the followingconditions: 1. This device may not cause harmful interference, and2. This device must accept any interference received,including interference...

Page 8 - Safety Compliance; Underwriters Laboratories Compliance Statement; Operating; UL Listed/CSA Certified Cord Set; Les raccordeurs ne sont pas utilisé pour le système téléphonique!

EtherHub-16 Quick Start Guide 8 You may find the following book prepared by the Federal Communication Commision helpful: The Interference Handbook This booklet is available from the U.S. Government Printing Office. Washington, D.C. 20402.Stock No. 004-000-00345-4. Safety Compliance Underwriters Labo...

Page 9 - oder Sprays verwenden, sondern ein angefeuchtetes Tuch.

EtherHub-16 Quick Start Guide 9 Sicherheitshinweise 1. Die Steckdose muß sich in der Nähe des Gerätes befinden und leicht zugänglich sein. 2. Zum Reinigen den Stecker aus der Steckdose ziehen. Beim Reinigen keine Flüssigreiniger oder Sprays verwenden, sondern ein angefeuchtetes Tuch. 3. Das Ethernet...

Page 10 - Copyright

EtherHub-16 Quick Start Guide 10 Warranty Accton warrants to the original owner that the product delivered in this package will be free from defects inmaterial and workmanship for the lifetime of the product. For the warranty to apply, you must register yourpurchase by returning the registration car...