Bose II - Manual
Bose II – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Operational Advisories
- Page 3 – If the above recommendations are not adhered to, the
- Page 4 – Declaration of Conformity; Bose; Headset; Electromagnetic Compatibility Susceptibility
- Page 5 – cushion replacement; Contents
- Page 6 – Introduction; Description; Congratulations on your purchase of the Bose; cushions require only; With the headset’s combination of both active and; Warranty card; Remove the headband cushion by pulling it away from the hook and
- Page 7 – For proper headset fit; The headset must be worn with the Bose logo (located on the; Figure 1; If you hear a hiss or a low rumbling sound, this may indicate an
- Page 8 – Interconnect plug; The illustrations below show the insertion of the headset inter-; Figure 2; Microphone placement; Figure 4; Using the Bose
- Page 9 – The volume controls and the active noise reducing circuitry; Figure 5; Figure 6; Fail-resistant operation
- Page 10 – Microphone boom relocation; Unscrew the retaining knob on the boom mic mount.; Figure 7; Find the crescent-shaped flanges on the top and bottom of the; Figure 8
- Page 11 – Plug the mic cable into the headband arm.; Headset cable relocation
- Page 12 – Powering the headset; Portable battery pack; The NICAD rechargeable battery pack:; Be sure to use the correct charger (Bose model numbers; The alkaline battery pack:; • Operates for approximately 40 hours; Charging the NICAD battery pack; Completion of the charging cycle is indicated by the flashing
- Page 15 – Installed connector; Installing the wire harness; Pin Wire
- Page 16 – Figure 9; PANEL HOLE REQUIRED
- Page 17 – Installed DC power connector; Installing the DC power connector; This installation must be done by mechanics qualified to
- Page 18 – Cleaning instructions; Do not immerse the headset in water.; Clear Comfort; cushion replacement and; To order a replacement cushion kit, call the Bose; To remove the cushion and foam liner; Do not use a hard object such as a screwdriver, which can mar; Care and Maintenance
- Page 19 – To install a new foam liner; The left and right foam liners are different.; To clean the cushion; Place the holes in the new cushion onto the posts on the earcup.; will not; fit on the right earcup.
- Page 21 – Technical Information
- Page 22 – Headset Weight; Operating Temperature:; The Bose; Condition
- Page 23 – Service; If your headset must be returned for service:; Warranty period; Service and Warranty Information
- Page 25 – Notes
Bose
®
Aviation Headset Series II
Owner's Guide
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 As with any complex electronic device, it is possible for this headset toexperience a failure during operation. Such a failure may include loudtones, distortion and loss of communications signal in the headset whenused in the active or “on” position. The system is “on” when the rockerswitch is “up...
3 Operational Advisories This headset meets or exceeds all requirements of EN352-4, 1996(European Standard-Hearing Protectors-Safety Requirements andTesting-Part 4: Level-Dependent Ear Muffs). • The wearer should ensure that: i. The ear muffs are fitted, adjusted, and maintained inaccordance with th...
4 Declaration of Conformity We, the offerer: Bose ® Corporation, The Mountain, Framingham, MA 01701-9168 USA acknowledge our sole responsibility, that the product: Kind of equipment: Headset Type designation: Bose Aviation Headset Series II in accordance with EMC Directive 89/336/EEC and Article 10(...
