Bosch SHEM63W55N/13 Installation Manual

Page 3 - Safety Definitions; NOTICE; WARNING; This indicates that minor or moderate injuries may occur as a; CAUTION

3 Safety Definitions This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory. NOTICE This indicates that death or serious injuries may occur as a result of non-observance of this warning. WARNING ! Note: This alerts you to important informat...

Page 4 - dishwasher performance.; IMPORTANT; 3′′ (84 cm) off the cabinet floor otherwise the dishwasher may not; Important Safety Instructions:

4 To avoid possible injury or property damage, OBSERVE ALL WARNINGS AND CAUTIONS. WARNING: These instructions are intended for use by qualified installers only. The dishwasher must be installed by a qualified service technician or installer.• In addition to these instructions, the dishwasher shall b...

Page 5 - Avoiding General Hazards; to tip over and result in serious injury.; Proposition 65 Warning:; product may bear the following label as required by California:; Inspect the Dishwasher; Cancer and Reprodutive Harm -

5 Avoiding General Hazards To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. Do not use the dishwasher until it is completely installed. When opening the door on an uninstalled dishwashe...

Page 6 - Tools and Materials Needed; Flat Screwdriver

6 Elbow connection with 3/4” female hose threads on one end and fits your water supply line (copper tubing, compression fitting, or braided hose) on the other. Hot Water Supply Line - Minimum 3/8 ″ O.D. copper tubing or metal braided dishwasher supply line. Only needed if house water supply line is ...

Page 7 - Materials Supplied; Power Cord; For fully integrated models only:

7 Materials Supplied Screw Clamp (for drain hose) Power Cord Mounting Brackets Mounting Bracket Screws Ø 4x13 mm Adhesive Backed Cord Clip D E F B A C Installation Guide for Fully Integrated Door Panel Vapor Barrier (included with some models) For fully integrated models only:

Page 8 - Toe Panel Kits; Slotted Toe Panel; Plastic Toe Panel

8 Toe Panel Kits (Model Dependent; your dishwasher is supplied with one of the toe panel kits shown below) Slotted Toe Panel 2 - Screws Ø 4x16 mm Non-Slotted Toe Panel 2- Screws Ø 4.2x12.7 mm Toe Panel Mounting Brackets (used with non- slotted toe panel shown above) G H I J K L Plastic Toe Panel M S...

Page 9 - Enclosure Requirements; To Avoid Scalding or Electrical Shock Hazard!; Make sure the water supply and electrical supply are shut off

9 Enclosure Requirements To Avoid Scalding or Electrical Shock Hazard! Make sure the water supply and electrical supply are shut off before installation or service. To Avoid Electrical Shock/Fire Hazard! Do not allow the electrical and supply lines to touch. Note: This dishwasher is designed to be e...

Page 13 - • Remove the hose clip at the back of the dishwasher as shown. The

13 • Remove the hose clip at the back of the dishwasher as shown. The hose clip may be used later to hold the drain hose inside your cabinet. 7 Avoid cross-threading! It will cause leaks. After attaching hose, temporarily hook up the water supply then turn on water to check for leaks. NOTICE DO NOT ...

Page 14 - Electrical Connection; Avoid Electrical Shock Hazard!; WARN; ING

14 Electrical Connection Avoid Electrical Shock Hazard! Do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circu...

Page 15 - Note: Installations requiring hard wiring and terminal block

15 Dishwasher Electrical Rating Volts Hertz Amperes Watts 120 60 12 1,440 (max) Electrical Supply The customer has the responsibility of ensuring that the dishwasher electri- cal installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed for...

Page 16 - • Place adhesive backed cord clip (provided in the installation kit)

16 Adhesive backed cord clip Leg Adjuster Strap 2" (5 cm) Alternate cable routin g 8 • Place adhesive backed cord clip (provided in the installation kit) 2 inches from leg adjuster as shown in the figure above and route power cord through the clip. Note:The length of cord measured from the plast...

Page 17 - Installation of Mounting Brackets; wood or other materials; Avoid Tip Over Hazard!; them is difficult and will damage the mounting brackets and the

17 Installation of Mounting Brackets • Top Mount is used for counter tops made of wood or other materials that can be easily drilled . If you have solid surface, marble, granite, or other very hard countertops, skip to step 10 now. • If insulation is covering the area in 9a, fold it back. • Orient t...

Page 19 - Positioning the Dishwasher

19 • If your sink is to the right side of where you are installing the dishwasher, you will need to reposition the hoses and power cord behind the dishwasher before installing. • To do so, unhook the strap that the hoses are running through on the back of the dishwasher base and position them per yo...

Page 22 - in; or counter top as shown.

22 • Adjust the legs as shown. Make sure the top of the door is no less than 6mm from the underside of the counter. • Use a level to check that your dishwasher is level. • Level side to side by turning feet clockwise to raise or counter- clockwise to lower front of the unit as shown. • Level front t...

Page 23 - Securing the Dishwasher; screws through the barrier for the Top Mount.

23 Securing the Dishwasher 17 18 E E • Drive the mounting screws (E) through the holes in the mounting brackets as shown for Top ( figure 17) or Side Mount (figure 18). • If the dishwasher came with a protective barrier, you should drill the screws through the barrier for the Top Mount.

Page 24 - Hot Water Supply; Water Inlet Connection; water supply is shut off.

24 Hot Water Supply The hot water heater should be set to deliver approximately 120° F (49° C) water to the dishwasher. Water that is too hot can cause some detergents to lose effectiveness. Lower water temperatures will increase run times. The hot water supply pressure must be between 15 - 145 psi ...

Page 25 - Drain Connection

25 Drain Connection • Connect the dishwasher water supply line to the water shut off valve. If one isn’t already in the supply line, install one (not provided). • You will need to use an approved dishwasher water supply line with the correct fittings for this connection. • After all connections are ...

Page 28 - the drain hose to the house plumbing

28 • Use the clamp provided (C) to attach the drain hose to the house plumbing as shown. 22 C

Page 29 - If the dishwasher came with a non-slotted toe panel (I) and toe panel; • Plug metal brackets (K) into openings on both sides of the base as; Attaching the Toe Panel; • Attach using screws (H) as shown. Use only the supplied screws to

29 If the dishwasher came with a non-slotted toe panel (I) and toe panel brackets (K) follow these instructions;otherwise skip to 27 now. • Plug metal brackets (K) into openings on both sides of the base as shown. • Use screw (H) to mount metal brackets to the base as shown. 24 H K Attaching the Toe...

Page 32 - Fully Integrated Door Panel; Please see the included instructions and template for

32 Fully Integrated Door Panel Please see the included instructions and template for installing a fully integrated door panel.

Page 33 - Customer Service

Your dishwasher requires no special care other than that described in the Care and Maintenance section of the Use and Care Manual. If you are having a problem with your dishwasher, before calling for service please refer to the Troubleshooting section in the Use and Care Manual. If service is necess...