BISSELL PROheat All-rounder EX7700E- User Manual

This user’s guide has been designed to help you get the utmost satisfaction from your BISSELL PROheat All-Rounder. You’ll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this user's guide thoroughly before assembling ...

Your BISSELL PROheat All-Rounder is a complete home cleaning system. Not only does it come with a lot of unique features, it has been designed with you, the customer, in mind. Built-in heater PROheat All-Rounder models all feature a patented built-in heater which heats the hot tap water you put in i...

S pecial features of your BISSELL PROheat All-Rounder Cleaning tools (continued) Multi-surface floor tool: May be used on both carpet/rugs or hard floor surfaces. For use on carpets, make sure the tab is in the down position . This will hide the soft outer brushes. For hard floor surfaces, press the...

Getting Ready (continued) 3 . Remove the collection tank from the unit by opening the Quick Release Hose Door and lifting the tank straight up by the handle. 4 . Remove the top lid from the collection tank and set aside. 5 . Fill the collection tank to the fill line (located on side of tank) with cl...

10 w w w . b i s s e l l . c o m Getting ready to wet clean NOTE: Remove tool caddy if in place. 1. Attach the desired wet cleaning tool to end of wand or grip. 2. Open the Quick Release™ Hose Door and select “WET CLEAN” with the mode selector. 3. Place the clean solution tank on a flat surface. 4. ...

11 w w w . b i s s e l l . c o m O peration Carpet Cleaning (continued) 7. Continue to clean entire carpet working in one meter by one meter sections. 8. If machine loses suction, stop spraying and check the collection tank level. Empty if necessary. 9. If the machine stops spraying turn off wet cle...

12 w w w . b i s s e l l . c o m O peration Hard floor cleaning (continued) 4. Attach microfibre pad to quick dry hard floor tool by attaching to the Velcro strips on the top of the tool. 5. Attach the quick dry hard floor tool to end of the wand. 6. Place tool directly on the hard floor surface, re...

13 w w w . b i s s e l l . c o m O peration Upholstery cleaning (continued) 2. Refer to the “Getting Ready to Wet Clean” on page 10. 3. Attach the desired wet cleaning tool to the wand or grip. 4. Clean by pressing the spray trigger to spray solution onto the area to be cleaned. Slowly move the tool...

M aintenance and care Machine storage Once your cleaning is complete make sure the dirty water from the collection tank is emptied. Rinsed out and dry before the next use. For wet cleaning, the solu-tion tank can be left filled and ready to use. Note: Store your PROheat All-Rounder in a protected dr...

M aintenance and care Machine care For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete. 1. Press all buttons OFF. Unplug the machine and wrap the cord. 2. After emptying the dirty water from the collection tank, rinse it out thoroughly with...

T roubleshooting Reduce Spray or No Spray Possible Cause Remedies 1. Make sure power is on 1. Press power button if needed 2. Solution tank may be empty 2. Fill tank according to directions 3. Tank may not be seated properly 3. Turn ON/OFF, heater and wet clean button off. Remove and reseat tank 4. ...

w w w . b i s s e l l . c o m R eplacement parts - BISSELL PROheat All-Rounder Below a list of common replacement parts*. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired. Item Part No. Part Name 1 203-7063 Mulit-Surface Floor T...