BISSELL BISSELL3437 - User Manual

6

BISSELL.com

3

1.

Locate stretch hose where it

connects to the hose elbow on

back of machine. Clean debris.

2.

Locate clear foot hose under hose holder. Remove two screws

and clear clogs and debris in the hose using a long narrow

object. Replace screws and re-attach stretch hose by sliding over

inlet and rotating upwards towards the lock position.

Note:

If the debris cannot be reached through the hose, follow the instructions for cleaning the air

passageway in “Maintaining the Brush Roll and Belts” section.

Cleaning the Hose and Foot

WARNING

To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet

before performing maintenance or troubleshooting checks.

©2022 BISSELL Inc. All rights reserved.

Part Number 1631065 07/22 RevH

Every Purchase Saves Pets

™

BISSELL proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets.

When you buy a BISSELL® product, you help save pets, too. We’re proud to design products that help

make pet messes, odors and pet homelessness disappear. Visit

BISSELLsavespets.com

to learn more.

Warranty

Limited 2-year warranty, may vary by state. Visit

support.BISSELL.com

or call 1-800-237-7691 for

complete warranty information.

For a comprehensive walkthrough of your product and support tips, visit

support.BISSELL.com

.

Troubleshooting

Important Safety Instructions ................................ 2
What’s in the Box? ......................................................... 2
Assembly .............................................................................. 3
Using Your Vacuum ....................................................... 3
Cleaning Above Floors ................................................4
Emptying and Cleaning the Dirt Tank ..............4
Cleaning the Filter .......................................................... 5
Maintaining the Brush Roll and Belts ................ 5
Maintaining the TurboBrush® Tool ......................6
Cleaning the Hose and Foot....................................6
Troubleshooting ...............................................................6
Warranty ...............................................................................6

CLEANVIEW ® COMPACT TURBO

U PRIG HT VACU U M

3 437 SERIES

Meet your new BISSELL product!

Go to

support.BISSELL.com

for a comprehensive walkthrough

of your new purchase, including videos, tips, support, and more.
Want to get started right away? This guide has all the information
you need to set up your new product. Let’s take a look…

WARNING

Before using your vacuum, make sure that the dirt tank is in locked position and that all filters,

both pre and post-filters, are in place. DO NOT operate your vacuum without these filters.

• To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet before performing

maintenance or troubleshooting checks.

1.

Insert handle into base with

tab facing back of vacuum.

Push down until it clicks.

2.

Wrap power cord around

upper and lower cord wraps.

3.

Attach TurboBrush® tool

holder to handle by lining up

the hole with the indent on

handle.
Attach tools by inserting onto

on-unit tool holders.

1.

Twist upper Quick Release™

cord wrap down to remove cord.

2.

Connect power cord plug to

a polarized outlet.

3.

Press the red power button

with your foot to turn the

vacuum ON

and OFF .

4.

Step on recline pedal and

pull handle back towards you.

Note:

To maneuver under

furniture, step and hold

the pedal to further recline

machine.

5.

Turn dial on foot to desired

height setting.

Tip:

For best performance,

adjust to the lowest practical

setting. If your vacuum is

difficult to push, adjust to the

next higher setting.

6.

To turn machine OFF ,

step on the power switch

pedal.
Once finished, loop power

cord around cord wraps.

Clip to power cord to secure.

Note:

Some Berber carpets may fuzz with wear. Repeated strokes in the same area may enhance this

condition.

Using Your Vacuum

Assembly

Go to

support.BISSELL.com

for assembly videos.

Maintaining the TurboBrush® Tool

For more helpful maintenance tips, check out

support.BISSELL.com

.

1.

Twist gray collar counter-

clockwise until slot appears,

then separate faceplate.

2.

Remove brush roll, belt

and paddle wheel. Inspect

for damages and replace if

necessary.

3.

To reassemble, align two

clips on each end of paddle

wheel with belt on and pop

back into place. Place brush

roll with belt back in. Faceplate

will not close properly if all

parts are not aligned correctly.

Product Overview

1. Extension Wand
2. TurboBrush® Tool
3. Crevice Tool
4. Tank Release Button
5. Dirt Tank
6. Dirt Tank Empty Button
7. Handle Recline Pedal
8. Extension Wand Release

9. Dusting Brush
10. Stretch Hose
11. Power Cord
12. Power Switch Pedal
13. Height Adjustment Knob

1

2

3

4

9

5

6

7

10

11

12

8

13