B&B Electronics 2IQEC4 - Manual

B&B Electronics 2IQEC4

B&B Electronics 2IQEC4 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
Page: / 22

Table of Contents:

  • Page 2 – Table of Contents; XT C
  • Page 3 – Chapter 1: Introduction; The 2IQEC2/4 is a 2/4 channel quadrature encoder 24 bit; Packing List; This instruction manual; Address Switch Setup; The 2IQEC2/4 cards use a 7-position DIP switch to program
  • Page 4 – Specifications; Address: Switch programmable, 0 to hex 7F0
  • Page 5 – Chapter 2: Installation; Software Installation; Address
  • Page 7 – IRQ; Table 3. Hardware Interrupts
  • Page 8 – Configuring the jumpers; The jumpers located on the left side of the card make it
  • Page 9 – Location of Jumpers
  • Page 10 – Software Registers; The FLAG register is a read-only register that holds the; FLAG Byte Defined; The following functions can be performed by writing to the; RLD Byte Defined
  • Page 11 – Filter Clock Prescalers; Each PSC is an 8-bit programmable modulo-N down; Counter Mode Registers (Write to Control Address); The counter’s operational mode is programmed by writing a; CMR Byte Defined
  • Page 12 – IOR Byte Defined
  • Page 13 – Index Control Registers (Write to Control Address); IDR Byte Defined
  • Page 14 – TROUBLESHOOTING; If you are unable to communicate with the card from your software:
  • Page 15 – I/O Map of XT Class Machines; Hex Address
  • Page 16 – Hardware I/O Map of AT Class Machines
  • Page 17 – Appendix B: Specifications; Appendix B: Specifications/Timing Diagrams; Pin Description; Ground; Addresses
  • Page 18 – Transient Characteristics; Quadrature Mode
Loading the manual

2IQEC2/43798 Manual

Cover Page

B&B Electronics -- PO Box 1040 -- Ottawa, IL 61350

PH (815) 433-5100 -- FAX (815) 433-5105

Quadrature Encoder Counter Board

Models:

2IQEC2

2IQEC4

Documentation Number 2IQEC2/43798

This product

Designed and Manufactured

In Ottawa, Illinois

USA

of domestic and imported parts by

B&B Electronics Mfg. Co. Inc.

707 Dayton Rd. P.O. Box 1040 -- Ottawa, IL 61350

PH (815) 433-5100 -- FAX (815) 433-5105

Internet:

http://www.bb-elec.com

[email protected]

[email protected]







1998 B&B Electronics -- September 1998

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Table of Contents; XT C

2IQEC2/43798 Manual Table of Contents i B&B Electronics -- PO Box 1040 -- Ottawa, IL 61350 PH (815) 433-5100 -- FAX (815) 433-5105 Table of Contents CHAPTER 1: INTRODUCTION ............................................................ 1 P ACKING L IST ................................................

Page 3 - Chapter 1: Introduction; The 2IQEC2/4 is a 2/4 channel quadrature encoder 24 bit; Packing List; This instruction manual; Address Switch Setup; The 2IQEC2/4 cards use a 7-position DIP switch to program

2IQEC2/43798 Manual 1 B&B Electronics -- PO Box 1040 -- Ottawa, IL 61350 PH (815) 433-5100 -- FAX (815) 433-5105 Chapter 1: Introduction The 2IQEC2/4 is a 2/4 channel quadrature encoder 24 bit counter card used to track the position of up to 4 separateencoders. This card is an ISA card that can ...

Page 4 - Specifications; Address: Switch programmable, 0 to hex 7F0

2 2IQEC2/43798 Manual B&B Electronics -- PO Box 1040 -- Ottawa, IL 61350 PH (815) 433-5100 -- FAX (815) 433-5105 Specifications Bus: IBM PC ISA Bus Slot: Requires 1 full length slot for complete IRQ selectability.When installed in a short slot, IRQs 10-15 will not be available.The four channel c...

Other B&B Electronics Models

All B&B Electronics Other