AudioSource Powered Subwoofer - Manual

PSW110 / 112

OWNER’S MANUAL

9200 North Decatur St. Portland, OR 97203 • 503.286.9300 • www.audiosource.net

3

1.

Volume Control

Adjusts output volume.

Power/Protect LED indicator

Illuminates green indicating the unit is turned on while switch is in “Normal” position,

or when receiving signal in “Auto-On” mode. Illuminates red during standby/protect mode.

Variable Crossover

Sets crossover frequency between 40Hz and 200Hz. For stereo music or home

theater, set the frequency to a level that sounds pleasing to your ear and the overall

reproduction of your audio. If using LFE signal, set crossover to 200Hz.

FRONT PANEL CONTROLS

3

2

1

Figure 1. Front Panel

Min

Max

Volume

40Hz

200Hz

Crossover

Power

PSW110

Protect

2.

3.

Input

L

L

R

R

Speaker Level Input

Line

+

+

-

-

Auto On Normal

Mode

180° 0°

Phase

PSW112

175W 12” Powered Subwoofer

PSW110

125W 10” Powered Subwoofer

Input

L

R

Line

Auto On Normal

Mode

180° 0°

Phase

Power

OFF

ON

115V~ 60Hz 300W

FUSE:T4AL 250V

FUSE:T2AL 250V

230V~ 50Hz 300W

Power

OFF

ON

Speaker Level Input

R

+

-

L

+

-

115V~ 60Hz 200W FUSE:T2.5AL 250V

FUSE:T1.25AL 250V

230V~ 50Hz 200W

7

6

4

5

9

10

8

4

5

6

7

8

10

9

4.

5.

6.

7.

Power Mode

Sets the power-on/off option of the PSW110/112. Set it to Normal for

manual control using switch . Set switch to Auto-On for automatic

power-on when signal is present; after 10 minutes with no signal, unit will

enter standby mode. For Auto-On the power switch is left in “ON” position.

Phase Control

Normally set to 0°. In rare instances, due to your unique sound system or the

size of your room, the output may be out of phase. If the sound is hollow

or the volume knob has little effect, set to 180° to compensate for these factors.

Line Level Input

Connect to the line level, subwoofer, or LFE output of your receiver, pre-amp,

or power amp.

Do not use

if Speaker Level Inputs are connected. For

single mono input: plug into either R or L terminal, or use a y-adaptor.

Speaker Level Input

Use when line level outputs are unavailable from your receiver, pre-amp or

power amp. Your existing stereo speakers can share these terminals, allowing

you to add bass to any stereo or home theater system. Always maintain

speaker polarity by connecting positive (+) and negative (-) terminals on

this unit with corresponding terminals on your existing speakers and source.

Do not use

if Line Level Inputs are connected.

Mains Power Inlet & Fuse Holder

Accepts IEC type line cord. A fuse located in the integrated holder provides

safety from fault conditions: replace fuse with one of same type and rating only.

Mains Voltage Selector

Voltage selection switch is preset to 115V (USA). For use in areas which

require 230V contact your dealer. Fuse must be of type and rating marked

on amplifier for use at local mains voltage.

Power Switch

Turns unit on and off in Normal power mode. Leave set to “ON” when using

Auto-On power mode.

8.

9.

10.

REAR PANEL CONTROLS

Figure 2. Rear Panel PSW110

Figure 3. Rear Panel PSW112

10

10

PLACEMENT

This unit features removable feet, a front firing woofer and ports, and front panel

controls for ease of use in a cabinet. The bass output of this unit is omnidirectional

so this unit may be placed anywhere in the listening environment. Walls or corners

will help reflect the bass for fuller sound. During use unit will vibrate: care should

be taken not to place any liquids or heavy items such as drinks or houseplants on

top as they may fall and damage your house or this subwoofer.

(Figure 1)

(Figures 2-3)