AudioSource AE8C - Manual
AudioSource AE8C – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – UL rated CL3; Installing the Speakers; Grill Removal for Installation
- Page 3 – Recommended Speaker Wire Gauges
- Page 4 – Two Year Limited Warranty
Congratulations on your purchase of the AudioSource
AE Series In-Ceiling Speaker System. This product is
designed to reproduce the audio portion of your
home entertainment environment with accuracy and
detail that will satisfy the most discriminating listener.
Please read this Installation Manual to ensure the
proper installation and performance of your AE Series
speakers.
Preparing for your Installation
Gather the necessary tools for your installation.
You will need the following tools:
1) A Keyhole or Drywall Saw
2) A Phillips Screwdriver
3) Masking Tape
4) A Pencil
5) A Tape Measure
6) A Stud Finder (recommended)
7) Your AE Series speakers
Placement
Plan your speaker placement carefully. Make certain
that electrical, plumbing and any other services will not
interfere within the ceiling where you plan to install your
speakers. The AE Series speakers can be mounted in
walls, but are typically used in ceilings. The speakers
should be located so that they provide even coverage
at your listening position. The distance between the
speakers should not be greater than the distance from
the speakers to the listening position (See Figure 1).
If the room’s dimensions or furniture placement prevent
adhering to this requirement, the tweeters in the AE
Series speakers can be swiveled to aim them at the
desired listening position.
New Construction
If you are installing your speakers in new construction
before the finished walls go up, AudioSource offers
New Construction Brackets, which provide a stable
frame that can be fastened to the wall studs or
ceiling joists on 16” or 24” centers. This allows the
sheet rock or other surface covering to be installed
and provides a template to cut the opening for the
AE Series speakers.
AE5C/AE6C/AE8C
Use a stud finder to locate the joists behind the ceiling
surface. Also, you should now check for obstructions
like cross bracing in front of and behind the desired
speaker location.
5“/6.5”/8” 2-Way In-Ceiling Speakers
11’
16’
20’
11.5’
Figure 1
Existing Construction
In most modern buildings ceiling joists are positioned
on 16” centers, providing a space between the joists of
approximately 14
3/8
”. The specifications chart shows
the appropriate cut out sizes (p. 4). Additionally, you
should allow an extra
3/4
” in all directions behind the
ceiling surface to allow room for the screw clamps that
mount the speaker to the ceiling to swing into position.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
After selecting the mounting location, mark the hole to be cut out. A template is provided in the speaker box. Locate and align the template, then mark with pencil on the ceiling surface. If you are unsure whether there are obstructions behind the ceiling surface where the speakers are to be mounted...
3 Tighten all four of the mounting screws in the same manner until the speaker is properly aligned and held tight to the ceiling surface. Painting the Speaker Two paint shields are included in each AE Series speaker package. Place the paint shield inside the frames to protect the speakers. You can n...
4 AE6C Specifications Woofer Tweeter Frequency Response Impedance Sensitivity Power Capacity Outer Dimension Cut Out Dimension Mounting depth 6.5” Carbon Filled Poly Cone w/Butyl Rubber Surround Pivoting 19mm Poly ferrofluid Cooled 50Hz to 20kHz 8 ohm 87dB, 2.83v @ 1m 10 to 100 Watts 9” (229mm) diam...
