Audio-Technica ATW-R3100b - Manual

Page 2 - Installation and Operation; RF Interference; Frequency Range

3000 Series Installation and Operation 2 This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210. Operation is subject t...

Page 3 - Receiver Installation; Figure A; Receiver Controls and Functions; Figure D

3000 Series Installation and Operation 3 is detected, reducing the possibility of interference. As a result, 3000 Series transmitters and receivers must be used together and should not be used with components from other Audio-Technica wireless systems, or with those of other manufacturers. Exception...

Page 4 - wait until the receiver’s Alert light

3000 Series Installation and Operation 4 be to the left (ground connected). If hum caused by a ground loop occurs, slide switch to the right (ground lifted). 12. BALANCED AUDIO OUTPUT JACK: XLRM-type connector. A standard 2-conductor shielded cable can be used to connect the receiver output to a bal...

Page 5 - Antenna Power; Transmitter Controls And Functions; LCD Window

3000 Series Installation and Operation 5 The squelch level is adjustable from 15 dB (the default value) to 39 dB in 6 dB steps. Increasing the squelch level – also called “tightening the squelch” – can cause a reduction in useable range of the wireless transmitter, so use the lowest value that relia...

Page 6 - Audio Input Selector

3000 Series Installation and Operation 6 modulation. When the transmitter is un-muted, it produces both RF and audio. To mute the transmitter (cut off the audio, but continue the RF output), press and release the Power/Mute button once . A small “MUTE” will appear in the LCD window, just below the f...

Page 7 - UniPak

3000 Series Installation and Operation 7 UniPak ® Transmitter Functions Function Menu Default Setting* Choices (Edit) ▲▼ Wrap-around (Transmitter powers-up at Frequency) ▲▼ Frequency Lowest in band† All frequenciesin band Yes ▲▼ RF Power RF LOW RF LOW, RF HI Yes ▲▼ Audio Input Level +6 dB –6 dB, 0 d...

Page 8 - Transmitter Setup

3000 Series Installation and Operation 8 Transmitter Setup Battery Selection and Installation Each transmitter uses two 1.5V AA batteries, not included. Alkaline type is recommended; other types of 1.5V AA batteries (including rechargeable) may be used, however performance may vary. Always replace b...

Page 9 - System Operation; Selecting/Setting Frequency

3000 Series Installation and Operation 9 System Operation Turn the receiver on by pressing in the Power switch. Do not switch on the transmitter yet. The Alert indicator and the LCD window will light up; the normal-operation LCD display will appear after 1-2 seconds ( Fig. D-1 ). If any of the bars ...

Page 10 - Setting Transmitter Audio Input Levels; Ten Tips to Obtain the Best Results

3000 Series Installation and Operation 10 4. Use the Up/Down arrow buttons to change the second three digits to the desired frequency. 5. To activate this frequency selection, press and hold the Set button until the word “STORED” appears in the transmitter’s window. (If you do not wish to complete t...

Page 11 - Troubleshooting Guide

3000 Series Installation and Operation 11 Troubleshooting Guide Receiver is not on (LCD window does not light). • Receiver Power switch is not pressed in. • Small DC power cord from included in-line power supply is not plugged into jack on back of receiver. (Use the cord hook to secure it.) • The in...

Page 12 - Specifications; Overall System; Open range environment with no interfering signals.; Transmitter

12 3000 Series Installation and Operation Specifications † Overall System UHF Operating Frequencies Frequency Range Number of Frequencies Band C: 541.500 to 566.375 MHz 996 Band D: 655.500 to 680.375 MHz 996 Band E: 795.500 to 820.000 MHz 981 Band F: 840.125 to 864.900 MHz 953 Band G: 721.500 to 746...

Page 15 - Statement of Compliance