AT&T TL7651 - Manual

CALL/FLASH Press to make or answer a call. During a call, press to receive call waiting (page 14). OFF/CLEAR During a call, press to hang up. While in menus, press to cancel the operation and exit the menu display.While predialing, press to delete digits (page 11). CHARGE light On when the remote di...

Avoid placing the remote dial pad too close to: • Communication devices such as: television sets, VCRs, or other cordless telephones. • Excessive heat sources.• Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting. • Excessive dust sour...

3 IMPORTANT INFORMATION Use only the power adapter supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com , or call 1 (800) 222-3111 . In Canada dial 1 (866) 288-4268 . The power adapter is intended to be correctly oriented in a vertical or floo...

4 Getting started Battery installation & charging Install the battery as shown below. After installing the battery, place the remote dial pad in the charger. For optimal performance, charge the remote dial pad battery for at least six hours before use. Insert the battery plug securely into the j...

5 Getting started Battery installation & charging Step 4 Charge the remote dial pad by placing it face up in the charger. The CHARGE light is on when the dial pad battery is charging. NOTE: 1. When the battery is charging, you will see the cycling . When the battery is fully charged, you will se...

Getting started Remote dial pad registration and de-registration The TL7601 remote dial pad allows you to place phone calls with an AT&T DECT 6.0 cordless headset system. You must register it to the TL7610/TL7611/TL7650/TL7651 headset base before use. The remote dial pad should be charged for a ...

PLEASE WAIT... 7 DIAL PAD 1 NOTES: 1. You cannot register a remote dial pad if a system headset is in use. 2. If the registration is not successful, the display shows NOT REGISTERED . Reset the remote dial pad by lifting it out of the charger and then placing it back in the charger. Now try the regi...

CONNECTING... NOT REGISTERED NOTE: De-registering the remote dial pad from the headset base also de- registers all the headsets. To use the remote dial pad or the headset again, refer to the registration information on pages 6-7. De-register the remote dial padPlease read carefully through all the i...

9 Getting started Belt clip To attach the belt clip: Snap the belt clip into the retaining tabs on both sides of the dial pad as shown in the figure. To remove the belt clip: Gently lift either of the belt clip retaining tabs, shown in the figure, to remove the belt clip from the dial pad.

10 Remote dial pad operation Remote dial pad settings Language You can select the language used for all screen displays. To select a language: 1. Press LANG/ SEL when in idle mode. 2. Use / to scroll to ENGLISH , FRANCAIS or ESPANOL . 3. Press LANG /SEL again to save your preference and return to th...

Remote dial pad operation Basic operation Make a call To make a call:• Press ON /OFF on the headset to turn on the headset, then enter the telephone number on the dial pad, and press CALL /FLASH on the remote dial pad. -OR- • Press ON /OFF on the headset to turn on the headset, then press CALL /FLAS...

Basic operation Last number redial (continued) To remove a number:• While the desired number is displayed, press DELETE to delete the displayed number from the redial memory. To edit a number: • While the desired number is displayed, press LANG/ SEL to enter the editing mode, then press OFF /CLEAR o...

Options while on calls Call waiting If you subscribe to call waiting service with your local telephone service provider, you will hear a beep in the headset if there is an incoming call while you are already on a call. Press CALL/ FLASH on the remote dial pad or press and hold the MUTE/ FLASH key on...

Remote dial pad operation Screen icons & display screen messages 15 Screen icons The remote dial pad works with headset 1. The remote dial pad works with headset 2. The telephone line is in use. Battery charging (animated display). 1 2 Display screen messages The remote dial pad is in idle mode....

Remote dial pad operation Screen icons & display screen messages 16 Display screen messages PLACE IN CHARGER UNABLE TO CALL TRY AGAIN NOT REGISTERED PRESS PAIR 4 SEC ON BASE The battery is very low. The dial pad should be placed in the remote dial pad charger for recharging. An attempt to make a...

Troubleshooting Troubleshooting If you have difficulty with your remote dial pad, please try the suggestions below. For Customer Service, visit our website at www.telephones.att.com , or call 1 (800) 222–3111 . In Canada, dial 1 (866) 288-4268 . 17 My remote dial pad doesn’t work at all. • Make sure...

18 Troubleshooting Troubleshooting • Reset the headset base. Unplug the electrical power of the headset base. Wait for approximately 15 seconds, then plug it back in. Follow the directions for remote dial pad registration. • You may need a new dial pad battery. Please refer to Battery installation &...

24 Troubleshooting Troubleshooting • Disconnect the power to the headset base.• Disconnect the remote dial pad battery.• Wait a few minutes.• Connect power to the headset base.• Re-install the battery, and place the remote dial pad into the dial pad charger. • Wait for the remote dial pad to re- est...

25 Maintenance and safety Maintenance Taking care of your remote dial pad Your remote dial pad contains sophisticated electronic parts, so it must be treated with care.Avoid rough treatment.Put the remote dial pad down gently. Save the original packing materials to protect your remote dial pad if yo...

Maintenance and safety Important safety information Replace batteries only as described in your user’s manual. Do not burn or puncture batteries — they contain caustic chemicals. This power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designe...

Maintenance and safety Important safety information or eliminate the interference. Rechargeable batteries: This product contains nickel- cadmium, nickel-metal hydride or lithium-ion rechargeable batteries. Exercise care in handling batteries in order to not create a short circuit with conductive mat...

Maintenance and safety Important safety information To prevent fire or shock hazard, do not expose this product to water or any type of moisture.Observe proper polarity orientation between the battery and the metallic contacts.Do not disassemble your telephone. There are no user-serviceable parts in...

Appendix FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the forma...

32 Appendix FCC Part 68 and ACTA Industry Canada Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.The term ‘’IC:‘’ before the certifica...

Appendix FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residentia...

Appendix Limited warranty The AT&T brand is used under license - any repair, replacement or warranty service, and all questions about this product should be directed to: In the United States of America, visit www.telephones.att.com or call 1 (800) 222-3111 . In Canada, call 1 (866) 288-4268 . Wh...

Appendix Limited warranty How long is the limited warranty period? The limited warranty period for the PRODUCT extends for ONE (1) YEAR from the date of purchase. If the manufacturer repairs or replaces a materially defective PRODUCT under the terms of this limited warranty, this limited warranty al...

Appendix Limited warranty PRODUCT returned without valid proof of purchase (see item 6 below); -or-Charges for installation or setup, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service? To obtain warranty service in the United Sta...

Appendix Limited warranty Other limitations This warranty is the complete and exclusive agreement between you and the manufacturer of this AT&T branded PRODUCT. It supersedes all other written or oral communications related to this PRODUCT. The manufacturer provides no other warranties for this ...

Appendix Technical specifications 39 Channels 5 Operating temperature 32°F — 122°F 0°C — 50°C Dial pad charger voltage (AC voltage, 60Hz) 96 — 127 Vrms Dial pad voltage 3.2 — 4.2 VDC Dial pad charger voltage (AC adapter output) 6VDC @200mA Replacement battery 3.7V 170mAH Dial pad operating range Thi...

A AC adapter, 3, 39 Answer calls, 12 B Basic operation, 11-13 Battery charging, 5, 15 Battery installation, 4, 5 Belt clip, 9 C Call waiting, 14, 22 CHARGE light, 1, 5, 22 D Delete digits, 1, 11, 13 Delete redial memory, 13 De-registration, 8 Dial pad operating range, 39 Display screen messages, 15 ...