Page 2 - Avoid placing the headset base too close to:; • Communication devices such as television sets, VCRs or other; Installation; STOP; For customer service or product information, visit our website at
Avoid placing the headset base too close to: • Communication devices such as television sets, VCRs or other cordless telephones. • Excessive heat sources.• Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators or fluorescent lighting. • Excessive dust sources su...
Page 3 - Quick reference guide - headset; On; Headset indicator lights
Quick reference guide - headset ON/OFF light status On Headset is charging in the headset base.Headset is trying to register to the headset base.Headset is searching for the headset base. ••• Flashing Flashes slowly when an incorrect type of battery is installed.Flashes three times, followed by a pa...
Page 4 - Battery cover
Quick reference guide - headset VOLUME / + - Press the volume keys on the side of the headset to adjust the listening volume when on a call. MUTE/FLASH Press to mute the microphone during a call.Press and hold to answer a call waiting call while on a call.Press to mute the ring tone in the earpiece ...
Page 5 - Headset alert tones
Three quick beeps VOLUME / + - keys are pressed when the volume is already at its highest or lowest setting.The headset is not registered and the headset ON/ OFF button was pressed. The headset is out of range from the headset base during a call. • • • One short beep every 0 seconds Low battery warn...
Page 6 - Quick reference guide - headset base; Charging cradle; PAIR; LIFTER MODE light; MUTE light
Quick reference guide - headset base Charging cradle Insert the headset here for charging. PAIR Press to register or deregister the headset. NO LIFTER MODE light On when NO LIFTER MODE is selected.Flashes while on a call, or another telephone is in use on the same line.Flashes quickly when there is ...
Page 7 - LIFTER AUDIO ADJUST; MODE
5 VOLUME / Press the volume keys on the side of the headset base to adjust the speaking volume while on a call. LIFTER AUDIO ADJUST Switch to choose the best headset audio quality when using LIFTER MODE . Quick reference guide - headset base MODE Press to choose between NO LIFTER MODE or LIFTER MODE...
Page 9 - Quick reference guide - handset lifter
Switch hook presser When the CORDED HANDSET CONNECTED switch is set to YES , pressing ON/OFF on the headset raises or lowers the switch hook presser. Lifter control cable This cable is hard wired into the lifter and plugs into the LIFTER jack on the headset base. RING DETECT jack Plug in the auxilia...
Page 10 - Small lifter pad; Adhesive tape; Internal ring detector; Switch hook presser adjustment knob
Small lifter pad Holds the earpiece of the corded telephone handset. Adhesive tape Remove the protective strips before attaching the lifter to the telephone base. STATUS light On in red when the ring detector is off. On in blue when the ring detector is on and the headset not in use.Flashes blue fou...
Page 11 - STATUS light; Red; LIFTER; jack on the headset base.
STATUS light Quick reference guide - handset lifter Red On when the headset is not in use and the ring detector is turned off. Flashes slowly when the headset is in use and the ring detector is turned off. • • Blue On when the headset is not in use and the ring detector is turned on. Flashes four ti...
Page 12 - Battery installation; THIS SIDE UP
0 Battery installation Install the battery as shown below. After installing the battery, you may be able to make and receive short calls. For optimal performance, charge the headset battery for at least six hours before use. When the headset is not in use, recharge the headset by returning it to the...
Page 13 - Battery charging
Battery charging After installing the battery, charge the headset by placing it on the headset base as shown below. The headset ON/OFF light is on when the headset is charging. CAUTION: There may be a risk of detonation if you use a wrong type of battery. Use only the supplied rechargeable battery o...
Page 14 - Headset base and lifter installation; Installation preparation; Install the headset base as shown on the following pages.
Headset base and lifter installation Installation preparation Before installing the headset base, remove the rear bottom piece of the headset base by pushing it away from the base (as shown in Figure ). Install the headset base as shown on the following pages. After completing installation option , ...
Page 15 - Headset base and handset lifter installation
Headset base and handset lifter installation No lifter mode or lifter mode There are two answer modes available on the headset base. The current mode is indicated by the NO LIFTER MODE or LIFTER MODE lights on the front of the headset base. When plugging your headset base into the telephone wall jac...
Page 16 - Cord labels
Headset base and handset lifter installation Cord labels The cords provided with your headset have colored labels attached to help you plug them into the headset base. The back of the headset base has colored dots above the jacks, and the names of the jacks on the rear bottom piece of the headset ba...
Page 17 - Installation options; You have three installation options:
5 Headset base and handset lifter installation Installation options You have three installation options: Option 1: Connect the handset lifter to a corded phone (pages - ). This option enables you to answer calls even if you are away from the telephone base. For this option, you can use the headset w...
Page 20 - Attach the lifter; . To choose where to install the lifter
Attach the lifter . To choose where to install the lifter on your telephone, look at the space underneath the corded handset. If there is a speaker, the lifter should be centered over the speaker. If there is no speaker, the lifter should be centered within the space. Make sure the lifter arm is rai...
Page 21 - Adjust the height of the lifter arm; Turn the; ADJUST LIFTER; knob to change the height of the lifter; Adjust the switch hook presser position
Headset base and handset lifter installation Adjust the height of the lifter arm Turn the ADJUST LIFTER knob to change the height of the lifter arm. When in the raised position, the arm should release the switch hook so you can hear a dial tone. When lowered, the arm should hold the switch hook down...
Page 23 - Installation of large lifter pad (optional); . Hold the large lifter pad in front of the small lifter pad as
Headset base and handset lifter installation Installation of large lifter pad (optional) If the small lifter pad cannot hold the corded handset steadily, you can attach a large lifter pad (provided) to enlarge the contact area. . Hold the large lifter pad in front of the small lifter pad as shown be...
Page 24 - Install the auxiliary ring detector; . Insert the auxiliary ring detector plug into the; . Remove the protective strip from the adhesive tape on the; About internal and auxiliary ring detectors
Install the auxiliary ring detector . Insert the auxiliary ring detector plug into the RING DETECT jack on the lifter. . Remove the protective strip from the adhesive tape on the auxiliary ring detector. . Stick the auxiliary ring detector to the center of the corded phone speaker. The internal or a...
Page 26 - Headset base installation; Option 2: Connect the headset to a telephone wall jack
Headset base installation Option 2: Connect the headset to a telephone wall jack In order to make calls using this installation option, you need a telephone plugged into the same telephone line or a dial pad (TL0 purchased separately). Make sure the headset base mode is set to NO LIFTER MODE . Plug ...
Page 27 - Option 3: Connect the headset to a corded or cordless phone
5 Headset base installation Option 3: Connect the headset to a corded or cordless phone To use this installation option, make sure the headset base mode is set to NO LIFTER MODE . Plug one end of the telephone line cord into the TEL WALL JACK (red dot) at the back of the headset base. • Telephone li...
Page 28 - Headset operation; When the headset base is connected to a corded or cordless
Headset operation Making a callWhen the headset base is connected to a corded handset of your telephone with the handset lifter installed (option 1): You must select LIFTER MODE on the headset base. Press on the headset. The switch hook presser rises and releases the switch hook. You hear a dial ton...
Page 29 - When the headset base is connected to a telephone wall jack,
Headset operation Answering a call on the headsetWhen the headset base is connected to a corded handset of your telephone with the handset lifter installed (option 1): Press ON/ OFF on the headset. The switch hook presser rises and releases the switch hook. You hear the caller through the headset ea...
