AT&T 902 - Manual
AT&T 902 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – I N S TA L L AT I O N
- Page 3 – c o n t i n u e d
- Page 4 – T E L E P H O N E O P E R AT I O N
- Page 5 – I N C A S E O F D I F F I C U LT Y
- Page 6 – M E M O R Y
Part 2
© 1998 Philips Consumer Communications, L.P. All rights reserved.
Printed in Mexico. 848236212 Issue 1AT&T
User’s Manual for the
Two-Line Speakerphone 902
Fold open this manual for information about
this telephone’s installation and operation.
Please r ead Part 1 — Important Product
Information, included in this package.
I N C A S E O F D I F F I C U LT Y
• Try calling the number you want
to enter into memor y. When the
call is ended, press
,
and a memory button.
• If someone lifts an extension
phone while you are storing num-
bers in memor y, programming
might be inter rupted. Make sure
all extensions are on hook while
storing numbers in memor y.
• You might not hear the confirma-
tion beep if the RECEIVER
(handset) volume is set too low, or
if you are in a noisy location.
• If the number is more than 24
digits long, make sure you follo w
the directions for “Dialing Long
Numbers.”
• Do not put the phone on Hold
while storing numbers.
Problems With Line Status Lights
• Make sure all plugs are connected
properly. Inspect the line cord
connections at the modular jack
and at the telephone . Also inspect
the coiled handset cord connections
at both ends.
• Try replacing old bat t e ries. See
“ B at t e ri e s ” in the Installation section.
• Make sure the batteries are
correctly installed, and that the
battery contact surfaces and
battery case are clean.
• If only one telephone line is
connected, make sure that only the
batteries for that line (as labeled
on the battery compartment) are
installed.
Telephone Does Not Ring
• Make sure the RINGER switch
is set in the LO or HI position.
• If there are several other
telephones on the same line, try
disconnecting some of the other
telephones. Having too many
telephones connected can also
create problems such as low ringer
volume, or impaired sound quality
during calls.
Other Problems
Make sure you have followed all the
instructions in this booklet. If you
continue to have problems, call
1 800 722-9125. If you cannot
correct the problem, disconnect the
telephone and refer to the warranty
information.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
I N S TA L L AT I O N NOTE: This telephone requires a 2-line modular jack or two separateone-line modular jacks to use thisunit as a two-line phone . NOTE: To use both lines of a two-line telephone, your local telephonecompany must provide two telephonenumbers. Batteries B e fo re using the telep h ...
I N S TA L L AT I O N c o n t i n u e d Table 1 Remove the base . 2 Connect line cord(s) to telep h o n e. • If you have a two-line jack, use only the line cord with theclear modular plugs on eachend. Plug one end into the jacklabeled L1 OR L1/2 on the bottom of the telephone . • If you have two sep...
T E L E P H O N E O P E R AT I O N Making a Call—Handset Press or and then lift the handset. You can dial your callmanually or use the memory dialingfeature. Answering a Call—Handset Each line has a different ringer toneto signal an incoming call. One ofthe Line Status lights will flash toidentify t...
