AT&T 1825 - Manual - manualsarea.com

Page 2 - I N S T A L L A T I O N; For Table/Desk Installation

I N S T A L L A T I O N 1 RING SELECT Telephone Line Cord MSG ALERT POWER Battery Installation (optional) 2 Connect the line cord to the telephone. Plug one end of the line cord into the jack labeled TEL LINE on the bottom of the telephone. Run the line cord through the channel on the bottom of the ...

Page 3 - For Wall Installation

Reverse the Handset Tab I N S T A L L A T I O N 3 2 1 PULL TABS TO OPEN PULL TABS TO OPEN PULL TABS TO OPEN Figure 1 Figure 2 Figure 3 Figure 4 For Wall Installation 1 Reverse the handset tab. (This tab holds the handset when you hang up.) Holddown the switchhook, and slide the tab up and out ofits ...

Page 4 - I N C A S E O F D I F F I C U L T Y

If this telephone does not work properly, tr y thefollowing suggestions. If you’re still having difficulty,call 1 800 222–3111. No Dial Tone • Make sure all plugs are connected properly. Check theline cord connections at the wall jack and at thetelephone. Also check the coiled cord connections tothe...

Page 5 - T E L E P H O N E O P E R A T I O N

T E L E P H O N E O P E R A T I O N 4 Hold To put a call on hold, press and release H . The HOLD light f lashes. You can return the handset to the cradlewithout disconnecting the call. To take a call off hold, press and release H — OR — Press K — OR — Lift the handset of this phone — OR — Lift the h...

Page 6 - T E L E P H O N E M E M O R Y; Storing Memory Numbers

5 T E L E P H O N E M E M O R Y PREVIEW Mute handset and speakerphone microphone Redial last number called Store numbers intelephone memory Microphone Temporary Tone Dial numbersin telephone memory Store a pause in amemory dial number When light goes on, battery needs replacement Light is on whenpho...

Page 7 - Setting the Clock; About Mailboxes; A N S W E R I N G S Y S T E M O P E R A T I O N

Setting the Clock You’ll need to set the clock so it can record the day andtime each message is received. 1 Press and release g . The Message Window displays CH . 2 Press and release C . The current day setting is announced. 3 To change the day setting, hold down / or ? until the correct day is anno...

Page 8 - Reviewing Your Announcement

A N S W E R I N G S Y S T E M O P E R A T I O N After the beep, the system begins recording your caller’smessage. A caller can leave a message up to three minuteslong. If the message is longer than three minutes, or if thecaller is silent for more than seven seconds, or if the systemruns out of memo...

Page 11 - R E M O T E O P E R A T I O N

Playing Messages in Another Mailbox After playing messages in one mailbox, the systemannounces “End of messages,” and beeps twice. You canthen press 1 (all messages) or 2 (new messages only) and enter the number of another mailbox ( 1 , 2 , 3 , or 4 ). Recording a New Announcement 1 Connect with the...

Page 12 - Memory Full; Voice Help Menu; Changing Your Remote Access Code; Turn System Off; Turn System On

Memory Full If the system answers after 10 rings and beeps twiceinstead of playing your announcement, the system is off,memor y is full, or the AO announcement is selected but not recorded. 1 Enter your Remote Access Code after the 2-beep signal. 2 Listen to messages, and delete some or all of them....

Page 13 - Tapeless Digital Answering System 1825

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ fold © 2000 Adv anced American T elephones. All rights r eserv ed. Printed in Me xico. 850002783 Issue 1A T&T 5/00 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ fold © 2000 Adv anced American T elephones. All rights r eser...

AT&T 1825 - Manual

Table of Contents:

Summary

Other AT&T Models