AT&T 1465 - Manual

4 Getting Started Parts checklist Remember to save your sales receipt and original packaging in case you ever need toship your telephone for warranty service. Check to make sure the telephone packageincludes the following: Telephone base Telephone handset Poweradapter Belt clip Battery pack Long lin...

5 Getting Started Before you begin About Caller Identification Caller ID with Call Waiting features inthis telephone let you see who’s callingbefore you answer the phone, evenwhen you’re on another call. Thesefeatures require services provided byyour local telephone company.Contact your telephone se...

6 Getting Started Telephone base installation Install the telephone base as shown below. Choose a location away from electronicequipment, such as personal computers, television sets or microwave ovens. Avoidexcessive heat, cold, dust or moisture. NOTE: Use only the power cord supplied with this prod...

7 Getting Started Battery installation & charging After installation, place the handset in the base and allow the battery to charge for 12hours before use. You can keep the battery charged by returning the handset to the baseafter each use. When battery power is fully depleted, a full recharge t...

8 Getting Started Wall mounting The telephone base can be installed on any standard wall-phone outlet as shownbelow. Choose a location away from electronic equipment, such as personal comput-ers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. Plug power cord transf...

9 Getting Started Belt clip & optional headset Install belt clip as shown below if desired.For hands-free telephone conversations, you can use any industry standard 2.5 mmheadset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches onside of handse...

10 Telephone Operation Press PROG to begin programming Press ^ or V to display features one by one Press SELECT to modify a displayed feature To stop at any time, press OFF Customizing your telephone Follow the steps below to program the telephone. Tostop at any time, press OFF . If the phone rings,...

11 Telephone Operation Customizing your telephone Choose dial mode 1 Press PROG to begin programming. 2 Press ^ until screen displays DIAL MODE & setting. 3 Press SELECT to change current setting: 4 Press ^ to display TONE or PULSE. 5 Press SELECT to select displayed dial mode and exit. Choose l...

12 Telephone Operation Making and answering calls Making and answering calls To answer an incoming call, press any key except OFF . To make a call, press PHONE , then dial a number. Press OFF to hang up. To preview numbers before dialing, enter numbers first,then press PHONE to dial. Press V at any ...

13 Telephone Operation Options while on calls Caller ID If you have Caller ID service, the caller’s number willappear on the display screen after the first ring (seepage 20 for additional Caller ID features and options). Call waiting If you have Call Waiting service, you will hear a beep ifsomeone c...

14 Telephone Operation Handset locator Handset locator If the handset is misplaced, press the PAGE/HANDSET LOCATOR button in the handset cradle on the base. The handset will beep for 60 seconds to help you find it.When the handset is found, press OFF to stop the beeping (or press the PAGE/HANDSET LO...

15 Directory Dialing Directory dialing The telephone directory in the handset can store up to50 names and telephone numbers. Each entry can contain a number up to 24 digits, and a name up to 15letters long. A convenient search feature can help youfind and dial numbers quickly (see pages 16-19). Spee...

16 Directory Dialing Speed dialing Numbers called most frequently can be stored in memorylocations 1-9 and dialed with only two button presses.You can enter 9 Speed Dial numbers up to 24 digitslong. Each number is stored in a one-digit memory location (1-9). To enter a Speed Dial number 1 Press PROG...

17 Directory Dialing 1 PROG 3 4 SELECT DIRECTORY 2 SELECT ENTER NAME PAT JOHNSON_ 5 PAT JOHNSON 5550100_ ENTER NUMBER 6 SELECT DISTINCT RING? N 5550100 7 SELECT NEW 00 OLD 07 1/01 12:00 AM Entering names into directory To enter a name Press dial pad buttons once for the first letter, twice forthe se...

18 Directory Dialing 1 DIR DIRECTORY 2 ^ ^ V ADAM 5551234 BETH 5554321 5 JOHN 5550123 Directory name search Follow the steps at left to browse through the tele-phone directory, or search to find a specific entry. Youcan press OFF at any time to exit the directory. To browse through the directory To ...

19 Directory Dialing 1 DIR DIRECTORY 2 ^ ADAM 5551234 3 SELECT SPEED EDIT ERASE 5551234 ^ SPEED EDIT ERASE 5551234 ^ SPEED EDIT ERASE 5551234 To move, edit or delete a listing When any listing is displayed, press SELECT to see options. Press ^ or V to highlight the option you want (blinking text), t...

20 Caller ID Operation How Caller ID works If you subscribe to Caller ID service provided by yourlocal phone company, information about each caller willbe displayed after the first ring. Information about the last 90 incoming calls is stored inyour call log. You can review the call log to find outwh...

21 Caller ID Operation 1 CID PAT JOHNSON 908-555-0100 8/12 10:06 AM NEW 03 2 V CHRIS WILLIAMS 908-555-1234 8/12 9:53 AM NEW 02 3 4 V MARK CLAYTON 908-555-5678 8/12 9:12 AM NEW 01 PHONE PHONE ON 9085555678 To review your call log When the phone is not in use, press CID to display information about th...

22 Caller ID Operation To dial a call log entry When any Caller ID screen is displayed, press PHONE to dial the number exactly as it appears on the screen. Dialing options Caller ID numbers may appear with an area code thatmay not be required for local calls. If the number displayed is not in the co...

23 Caller ID Operation To delete call log entries To delete a single call log entry Press CID , to display the first Caller ID listing. Use the up/down arrow keys to find the entry you want todelete, then press CHAN/DELETE . When the entry is deleted, the next oldest record is displayed. To delete a...

24 Caller ID Operation 2 SELECT ^ DIAL PROGRAM 908-555-0100 8/12 10:06 AM NEW 03 3 SELECT PAT JOHNSON 9085550100 6 SELECT PAT JOHNSON 908-555-0100 8/12 10:06 AM NEW 03 To add entries to phone directory When any Caller ID screen is displayed, follow thesteps at left to enter it into your phone direct...

25 Answering SystemOperation Message capacity The answering system can record up to 99 messages, depending on the length of each message.Individual messages can be up to 4 minutes long, buttotal maximum recording time is 15 minutes. Messageswill remain available for replay until you delete them. 16 ...

26 Answering System Operation Day and time announcements To set day and time Before playing each message, the answering systemannounces the day and time the message was received. Before using the answering system, you should followthe steps at left to set the day and time, so messagesare dated corre...

27 Answering System Operation Outgoing announcements Outgoing announcements are the messages callers hearwhen calls are answered by the answering system.The phone is pre-programmed with an announcementthat answers calls with “Hello. Please leave a message after the tone.” You can use this announceme...

28 Answering System Operation Announce Only mode In Announce Only mode, callers hear an announcementbut cannot leave messages. This option is useful, forexample, to notify callers that you will be away for anextended period and request that they call back after acertain date. To turn Announce Only o...

29 Answering System Operation Changing feature options Menu features can be changed to customize how theanswering system operates. Press MENU repeatedly to hear each feature. Press CHANGE when you hear the feature you want to modify. Feature options (Default settings underlined) System announces: Fe...

30 Answering System Operation Message playback Press the PLAY/STOP button to hear incoming messages you’ve received. The system announces the number ofmessages, then begins playback.If you have new messages waiting, you will hear only thenew messages (oldest first). If there are no new messages,the ...

31 Answering System Operation Recording and playing memos Memos are messages you record yourself. They aresaved, played back and deleted exactly like incomingmessages from callers. You can record a memo as areminder to yourself, or leave a message for someone elseif others in your household use the ...

32 Answering System Operation Message window displays The message window usually displays the total number ofmemos and incoming messages. See list below for explanation of other displays in this window. Message window displays 0 No messages. 1-98 Total number of messages & memos, or messagenumbe...

33 Answering System Operation 1 Remote access A two-digit security code is required to access youranswering system from any touch-tone phone. Thiscode is “19” by default; see page 29 to change it. Dial your telephone number fromany touch-tone phone 2 When system answers, enter 2-digit Remote Access ...

CONNECTING... The handset is waiting for a dial tone. NEEDS RECHARGING Handset battery is depleted. Place handset in base to charge the battery. BATTERY LOW Handset battery is low. Place handset inbase to charge the battery. RINGER OFF The handset ringer is turned off. HOLD Current call is on hold. ...

35 Appendix “Beep-Beep ... Beep-Beep ...” (Double beep every 5 seconds) Handset battery is low. Place handset inbase to charge the battery. “Beep” (Single beep) Handset has registered with base andcan be used. “Beeeeeeeeep” (1 long beep) Confirm tone (current operation has beensuccessfully completed...

36 Appendix In case of difficulty If you have difficulty with your phone, please try the suggestions below. For CustomerService, visit our web site at www.telephones.att.com , or call 1 800 222–3111. Telephone doesnot work at all • Make sure the battery pack is installed and charged correctly (seepa...

38 Appendix A AC adapter, 6 Access code, 29, 33 Alert tones, 35 Answering calls, 12 Answering system, 25 announce only, 28 delete messages, 30, 33 feature options, 29 outgoing announcement, 27, 33 memos, 31 message window, 32 play messages, 30, 33 remote access, 33 remote access code, 29, 33 Antenna...

40 Appendix Technical specifications RF Frequency Band(Handset to Base) 912.75MHz — 917.10MHz Output Power 3 dBm Sensitivity -108 dBm Modulation FM RF Frequency Band(Base to Handset) 2411.15MHz — 2418.4MHz Channels 30 Channel Spacing 300 KHz Operating Temperature 32°F — 122°F0°C – 50°C Base Unit Vol...

Appendix Your package includes a handy wallet card to help you remember access commandsyou can use to control your answering system from any touch-tone telephone.If you misplace this card, just clip and save the card below. Remote access wallet card Cut along dotted line Fold card here Action Remote...