Page 3 - Table of Contents; ISDN R
ii Table of Contents C HAPTER 1............................................................................................................................................... 1 I NTRODUCTION ................................................................................................................
Page 4 - An overview of the ISDN Router; ISDN Router
1 Chapter 1 Introduction 1.1 An overview of the ISDN Router The device is a small desktop router that sits between your local Ethernet network and a remote network (For example, the Internet or a remote office). It contains an ISDN S/T interface, a 10/100 Base-T LAN port, and an auxiliary port for a...
Page 5 - ISDN Router Features; ISDN Router Application
2 1.3 ISDN Router Features The ISDN Router provides the following features The router equipped with a single ISDN Basic Rate Interface (2B+D) that supports S/T interface specification, would support European ISDN requirements. Supports remote access functions among branch offices and allows remote u...
Page 6 - Cautions for using the ISDN Router
3 Chapter 2 Using the ISDN Router 2.1 Cautions for using the ISDN Router Do not place the ISDN Router under high humidity and high temperature. Do not use the same power source for ISDN Router with other equipment. Do not open or repair the case yourself. If the ISDN Router is too hot, turn off the ...
Page 9 - Before Configuration
6 Chapter 3 Configuration 3.1 Before Configuration This section describes the configuration required by LAN-attached PCs that communicate with ISDN Router, either to configure ISDN Router, or for network access. These PCs must have an Ethernet interface installed properly, be connected to ISDN Route...
Page 11 - Configuring PC in Windows NT4.0
8 Configuring PC in Windows NT4.0 1. Go to Start/Settings/ Control Panel . In the Control Panel double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties . 3. Select the Obtain an IP address from a DHCP server radio button and click OK .
Page 12 - Configuring PC in Windows 2000
9 Configuring PC in Windows 2000 1. Go to Start/Settings/Control Panel . In the Control Panel double-click on Network and Dial-up Connections . 2. Double-click Local Area Connection . 3. In the Local Area Connection Status window click Properties . 4. Select Internet Protocol (TCP/IP) and click Prop...
Page 13 - Configuring with GUI program; Using Different Browsers for ISDN Router
10 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. 3.2 Configuring with GUI program 3.2.1 Using Different Browsers for ISDN Router To configure your ISDN Router, you can use a popular browser, su...
Page 14 - Basic Internet Access Configuration
11 3.2.2 Password A password screen will ask you to log on after you enter the default IP address described above. If you are logging on for the first time, you should accept the factory default password (which is “password”). The password is always displayed as a string of asterisks (“*”). Clicking...
Page 15 - Internet Access with Advanced Configuration
12 When you apply for an account with your Internet Service Provider (ISP), you will be given the necessary information, including your account name, account password, and the ISP’s local access ISDN telephone number. Have these available and then follow the steps below. Step 1: When you logon, sele...
Page 17 - IP Configuration for Internet Access
14 One B Channel Only: Two B Channels Only When Needed: Always two B Channels: Step 7: Select Data Service . Available options are Data Over Voice Channel , 64K , 56K , and Auto . Recommended selection is Auto . Step 8: Enter Remote Sub Address Number if necessary. Step 9: Select STAC compression op...
Page 20 - IP Address Translation Configuration
17 Gateway: identifies if the gateway is an IP address or interface. Hop Count: the maximum number of hops for this route. Step 3 Click APPLY . 3.2.8 IP Address Translation Configuration For security and economic purposes, the device supports Single User Account feature (SUA). Multiple users in the ...
Page 21 - Add or Edit IP Address Translation
18 3.2.9 Add or Edit IP Address Translation Step 1 : Click Address Translation button in the Advanced Internet Access Setup screen. The following IP Address Translation Configuration screen will appear. Step 2: Click Add for adding a set of IP address translation, or click Edit for editing an existi...
Page 22 - Add or Edit a Set of static private IP address
19 Private Port Number: The private port number corresponding to the service that the specific server provides. Public Port Number and Private Port Number should be the same. Step 4: Click Apply . Delete a Set of IP Address Translation Step 1: Select the set of IP address translation that you want t...
Page 23 - Delete a Set of static private IP address
20 Name: A name is assigned for router manager identification purpose. IP Address: The static private IP address that you want to assign. MAC Address: The MAC address of the physical interface between the device and the PC or workstation. Step 3 : Click Apply . Delete a Set of static private IP addr...
Page 24 - Remote Office Access by ISDN
21 Chapter 4 Remote Configuration The remote site does not have to have an ISDN router, and may not be configurable by the local administrator. Make sure the configuration matches the requirements of the remote site 4.1 Remote Office Access by ISDN To configuring the ISDN interface for Remote Office...
Page 26 - Advanced Options for Remote Office Access Profiles
23 Make sure the remote site is configured with the same values you specify in My System Name and My System Password. Remote System Name: Remote System Password: Step 6: If you selected Outgoing or Both as your Call Direction , click APPLY and TEST , or select ADVANCED for more options. You must sti...
Page 28 - Deleting Remote Office Access Profile
25 Step 5: Select the Number of Alternative Remote Phone Numbers and then enter the remote phone numbers in the corresponding blanks. Click OK to back to the previous screen. Step 6: Click OK to back to main configuration screen and click Apply and Test . 4.3 Deleting Remote Office Access Profile Fo...
Page 31 - Packet Filtering
28 Step 8: Click OK to back to the previous screen and click OK again to back to Connection Profile Configuration screen. 5.2 Deleting Dial-in User Profiles Follow the steps to delete a Dial-in User Connection Profile. Step 1: Select Connection Profiles from the Menu Window. Step 2: Highlight the en...
Page 33 - How to Upgrade the Firmware
30 Chapter 6 Management 6.1 How to Upgrade the Firmware Step 1: Select System Upgrade from the Menu Window. The following screen is displayed: Step 2: To update ISDN Router firmware, download the firmware from Atlantis Land’s web site and install the firmware in your local environment first, then fr...
Page 34 - How to Change ISDN Router Manager Password
31 6.3 How to Change ISDN Router Manager Password After you start using the ISDN Router, you should change the factory default password. Follow the steps to change the password. Step 1: Select Change Password from the System Tools Menu: The following screen displays: Step 2: Enter the following info...
