APC NET9RMBLK - Manual

SAVE THESE INSTRUCTIONS!

Thank you for selecting the SurgeArrest Rackmount from American
Power Conversion! It is designed to provide the highest degree of
protection from utility line spikes, surges and EMI/RFI noise. Please
complete and return the enclosed warranty registration card.

Surges are caused by nearby lightning activity and motor load switch-
ing created by air conditioners, elevators, refrigerators, and so on. The
SurgeArrest Rackmount filters out EMI/RFI (electromagnetic and
radio frequency interference) noise with components whose electrical
resistance is very high at radio frequencies. EMI/RFI noise is com-
monly created by the same activity, which produces surges, and can
also be caused by nearby radio transmitters.

Before installing the unit, ensure you have read and understand the
following safety instructions:
•

The SurgeArrest Rackmount supressor is intended for indoor use
only. Do not install this product where it is exposed to excessive
moisture or heat.

•

Never install any wiring or products during a lightning storm.

•

Plug the SurgeArrest Rackmount supressor into a

3-wire,

grounded

outlet only. If the

SITE WIRING FAULT

indicator is

illuminated, contact a qualified electrician to correct the service
wiring.

•

The SurgeArrest Rackmount is designed to be mounted in a vari-
ety of orientations in an equipment rack. Brackets with multiple
hole patterns can be easily installed in either a horizontal or verti-
cal orientation, as shown in the diagrams below, and to the right.

•

Do not use extension cords or adapters with this product.

CAUTION

: Do not install this device if there is not at least 10 meters (30

feet) or more of wire between the electrical outlet and the electrical ser-
vice panel.

Important Safety, Grounding and
Installation Instructions

SurgeArrest Rackmount -- Front and Rear Views

•

Two W

ire Guides

are provided to neatly bundle the line cords of

the equipment being protected. Four

Plug Pull-out Guards

are

provided. Use these to prevent cords from accidental disconnec-
tion from suppressor receptacles, shown in the diagram below.

•

The

Switch Guard

prevents power from accidentally being

turned off.

•

Rack mount ears are included, and are pre-installed for conve-
nience. If required, they can be attached.

•

A

15-foot power cord

provides additional convenience in posi-

tioning the rack system into place.

Operation

The

Site Wiring Fault Indicator

(red) will illuminate if the building

wiring is faulty, regardless of the position of the On/Off Switch. This
indicator signals either: missing ground wiring, the hot and neutral
wires are reversed, or the neutral circuit is overloaded. If this indicator
is illuminated, a qualified electrician should be called to correct the
service wiring. When SurgeArrest Rackmount is fully loaded, the Site
Wiring Fault indicator may flicker - this is normal and may not be
indicative of a fault. Even if equipment appears to operate normally,
faulty wiring could result in a shock hazard that can prevent the
SurgeArrest Rackmount from providing rated surge and noise sup-
pression.

Note:

The

Protection Working

LED (green) indicator is normally illumi-

nated when the switch is activated. The light is off when SurgeArrest Rack-
mount has disconnected itself from the utility due to a sustained ultra high
energy surge, such as a direct lightning strike. If you observe that this LED
indicator is off, first check the Circuit breaker and On/Off Switch to make sure
that the suppressor is on and receiving power. If the Protection Working LED
still does not light, return the unit to APC to be repaired or replaced.

The

Circuit Breaker

is tripped when the button pops out. This indi-

cates the suppressor is overloaded, and at least one supported device
needs to be unplugged. The circuit breaker is rated to trip at the same
overload point as most home and office utility service branch protec-
tors (15 Amps).
The

On/Off Control

regulates power to the eight switched outlets, and

can be used as a system master switch to all nine switched outlets.

Mounting Procedures

Study the diagrams on this page for rack mounting options. All
required brackets and screws are provided.

RACKMOUNT SURGE ARREST

VERTICAL MOUNTING OPTIONS

990-2466A 11/09

HORIZONTAL RAIL MOUNTING

VERTICAL EIA RAIL MOUNTING

22.50" MAX

IN TE RIOR HOR IZONTAL
MOUN TING R AILS

UNIVE RSAL MO UNTING

BRACKET

VERTICAL EIA RAIL

(PERSPECTIVE ILLU STR ATES LO OKIN G
INTO R EAR O F CAB IN ET)

(PERSPECTIVE ILLU STR ATES LOOK IN G
TH ROUG H SIDE OF C ABINET)

VERT ICAL EIA RAIL

UNIV ERS AL MOU NTING
BR ACKET

AS SEMBLY MO VEMENT

FO RWAR DS OR

BACKWAR DS UP TO 2''

REAR VIEW

3.50"

15A POWER CORD

15' LONG

(9) SWITCHED OUTLETS

GR OUN D S CREW

UNSWITCHED
CONV ENIEN CE OUTLET

PROTECTION WORKING

LED (GREEN)

FRONT VIEW

19.00"

o

LED(RE D)

CIRCUIT BREAKER

ON/OFF ROCKER SWITCH