Ampeg SVT-5 PRO - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS; SVT-5 PRO Bass Amplifier; IMPORTANT SAFETY INSTRUCTIONS; Declaration Of Conformity; SLM Electronics; Complies with Standards:

2 TABLE OF CONTENTS Introductions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Important Safeguards and Precautions . . . . . . . . . . . . . . .3The Front Panel Controls and Their Use . . ....

Page 3 - An Introduction to your new Ampeg SVT-5 PRO Bass Amplifier; them prior to using the amplifier.; Features; • GATE SWITCH: Keeps things quiet in between riffs

3 An Introduction to your new Ampeg SVT-5 PRO Bass Amplifier Thank you for making one of the best choices you will ever make for your musical career – choosing one of the finest bass amps available, the Ampeg SVT-5 PRO. This versatile and powerful bass amplifier delivers up to 1350 watts of unsurpas...

Page 4 - The Front Panel Controls and Their Use

4 The Front Panel Controls and Their Use SVT-5 PRO Bass Amplifier 1 4 8 10 13 22 28 29 23 9 5 24 27 2 3 6 7 11 12 25 26 14 17 18 19 20 21 30 15 16 1. INPUT: Connect your bass guitar here by meansof a shielded instrument cable. 2. -15dB: This switch, when depressed, will atten-uate the input signal b...

Page 5 - The Rear Panel; jacks are recommended when playing at full

The Rear Panel SVT-5 PRO Bass Amplifier SVT5PRO CLEAN POSTCLEAN PRE * OVERDRIVE MIX 32 33 34 35 36 44 31 45 46 47 48 49 50 51 52 53 54 41 37 38 39 40 42 43 31. AC OUTLET: This unswitched outlet provides aconvenient source of AC power for effects units, anelectronic tuner, power amplifier, etc. The o...

Page 6 - Connections; jack to the input of a full range speaker cabinet; Mono; Dual; • Connect a heavy duty speaker cable (

6 Connections SVT-5 PRO Bass Amplifier MONO BRIDGED: The SVT-5 PRO’s two internal amplifiers are bridged together to produce maximum output power. • Full Range/Biamp switch out (full range), Stereo/Mono switch depressed (mono)• Connect a heavy duty speaker cable ( ) from the SVT-5 PRO’s Mono Bridge/...

Page 7 - BIAMP WITH A SECOND AMP:; Biamp with a

Connections SVT-5 PRO Bass Amplifier BIAMP - Highs / Lows: One of the SVT-5 PRO’s internal amplifiers will power a high frequency cabinet, the other will power a low frequency cabinet. • Full Range/Biamp switch depressed (biamp), Stereo/Mono switch out (stereo)• Connect a heavy duty speaker cable ( ...

Page 8 - Some Suggested Settings

8 Some Suggested Settings SVT-5 PRO Bass Amplifier OUT OUT IN OUT OUT OUT OUT OUT IN OUT IN OUT IN OUT "SVT" "SMOOTH" IN IN IN IN OUT OUT "METAL" "SLAPPIN'" OUT OUT OUT OUT IN IN "EDGE" IN IN OUT OUT IN IN "SYNTH" IN IN OUT OUT IN IN "THREE GUYS JA...

Page 9 - Rack Mounting

9 SVT-5 PRO Bass Amplifier Rack Mounting When mounting the SVT-5 PRO into a rack, the four bottom feet should be removed to maintain the three rack space height of the amplifier. Be sure to keep the feet and their attachment bolts for future use. If the feet are reinstalled, never use screws which w...

Page 10 - System Block Diagram

10 System Block Diagram INPUT -15dB PAD MUTE FOOTSWITCH OCTAVE FOOTSWITCH SWITCHING JACK OCTAVE PREAMP OUT OVERDRIVE PREAMP OUT TUNER OUT TUBE STAGE PEAK/ MUTE ULTRA LOW ULTRA HIGH ON BOOST BASS MID TREBLE GAIN VOLUME MASTER OCTAVE CH. SELECT COMBINE TONES CMPRSN LOGIC GATE EFFECTS LOOP GAIN MID VOL...

Page 12 - Technical Specifications; Ampeg – The Power of Bass

Ampeg reserves the right to change specifications without notice. Made with Pride in the U.S.A. by Ampeg • ©2001 AMPEG, 1400 Ferguson Avenue, St. Louis, MO 63133 U.S.A. P/N 47-618-51 • 08/01 Technical Specifications OUTPUT POWER RATING 1350 Watts Mono-Bridged @ 4 Ohms (1000 Watts Continuous) 840 Wat...

Ampeg SVT-5 PRO - Manual

Table of Contents:

Summary

Other Ampeg Models