American Standard T385.507 - Manual

Certified to comply with ANSI A112.18.1

3

2

INSTALL TRIM

ADJUST HOT LIMIT STOP

B AT H A N D S H O W E R T R I M K I T S

1

4

5

13

12

3

2

1

9

7

8

10

11

6

When finished tiling the wall, remove PLASTER GUARD (3).

Push on CAP (1).

Mount ESCUTCHEON (2) and with SCREWS (7).

Install HANDLE (8) by pushing it onto CARTRIDGE STEM (9)

and tightening SET SCREW (10) from below with 2.5mm

Hex Wrench supplied. Insert INDEX BUTTON (11).
Remove cap from tub supply and plug from shower pipe.

Install SHOWER ARM (4) and FLANGE (13). Install

SHOWER HEAD (5).

See Step 2

.

Tighten SET SCREW (12) onto FLANGE (13)

using 5/64” hex wrench.

Install DIVERTER SPOUT (6).

R e l i a n t 3

R e l i a n t 3

By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP

reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust

the setting on the HOT LIMIT SAFETY STOP.

Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to

adjust min./max. discharge temperature. "0" being the hottest to "7" the coldest temperature setting. Factory set at "0".

HOT LIMIT SAFETY STOP ADJUSTMENT

PRY RED RING FORWARD AND ROTATE

COUNTER-CLOCKWISE ONE CLICK

PRY RED RING FORWARD AND ROTATE CLOCKWISE

"A"

ADJUSTMENT WHEN WATER IS TOO HOT

"A"

"B"

"B"

ADJUSTMENT WHEN WATER IS TOO COLD

"RED RING"- HOT LIMIT SAFETY STOP

TEMPERATURE SETTING NUMBERS

0

1

2

3

4

5

6

1

SERVICE

4

Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inlets

and MANIFOLD (5).

Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).

Replace CAP (2) and HANDLE (1). Check flow.

If faucet drips, operate handle several times from "off" to "on". Do not apply excessive force.

Clogged CARTRIDGE (4) inlets may cause reduced flow in "full on" hot or cold. To clean inlets, first turn off

water supply, then:

Installation

Instr uctions

T 3 8 5 . 5 0 8

T 3 8 5 . 5 0 7

BATH/SHOWER

TRIM KITS

MODEL NUMBER

CHROME

002

SATIN NICKEL

295

Replace the "YYY" with

appropriate finish code

5

4

3

2

1

060351-YYY0A

SHOWER ARM

AND FLANGE

M953016-YYY0A

SHOWER HEAD

M962490-YYY0A

ESCUTCHEON AND SCREWS

M907050-YYY0A

ESCUTCHEON CAP SET

M950231-YYY0A

DIVERTER SPOUT (SLIP-ON)

M962497-YYY0A

LEVER HANDLE KIT

THREADED INLETS (STOPS)

INLETS

1/2" NPT

5-7/8"

OUTLETS

1/2" NPT

3-3/8"

INLETS 1/2" NPT

OUTLETS

1/2" NPT

3-3/8"

3-3/8"

THREADED INLETS

INLETS

4-1/16"

4-1/16"

INLETS

1/2" NOM.

COPPER

SWEAT

SHR. 1/2" NOM.

COPPER SWEAT

TUB 1/2" NOM.

COPPER SWEAT

2"

SWEAT

INLETS

SHR. 1/2" NOM.

COPPER SWEAT

TUB 1/2" NOM.

COPPER SWEAT

4-1/16"

5-7/8"

SWEAT

INLETS (STOPS)

INLETS

1/2" NOM.

COPPER

SWEAT

M 9 6 8 6 9 0

M 9 6 8 6 9 0

M 9 6 8 6 9 0

M 9 6 8 6 9 0

Teflon Tape

Flat Blade Screwdriver

Plumbers' Putty or Caulking

Phillips Screwdriver

To assure proper positioning in relation to wall, note

roughing-in dimensions.

ROUGHING-IN DIMENSIONS

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

© A S A m e r i c a , I n c . 2 0 0 7

IN MEXICO 01-800-839-12-00

FINISHED WALL

4"

TOP OF TUB RIM

BOTTOM OF TUB

74" FOR HEAD

CLEARANCE

4-1/4" REF.

18" OPTIONAL

5-1/2" REF.

1/2" NPT

1/2" COPPER

7-5/8”

1-1/2" REF.

6" REF.

"SEE ILLUSTRATION "

3/4"" TO 2-3/8"

SHR

TUB

OPTIONAL TO FINISHED

FLOOR USUALLY

BETWEEN 65'' AND 80''

1-1/2" REF.

T 3 8 5 . 5 0 8

T 3 8 5 . 5 0 7

078016-YYY0A

ESCUTCHEON SCREWS

Adjustable Wrench

RECOMMENDED TOOLS

REMOVE SHOWER HEAD FROM HOUSING

1

1

2

Hold SHOWERHEAD (1) with one hand and HOUSING (2)

with the other as illustrated.

Rotate SHOWERHEAD (1) clockwise while holding HOUSING (2)

stationary.

NOTE: The thread connection is a left hand

thread.

Keep turning SHOWERHEAD (1) until it can be

removed from the HOUSING (2).

2a

INSTALL HOUSING

INSTALL SHOWER HEAD ASSEMBLY

2c

Slide HOUSING (2) onto

SHOWER ARM (3).

2b

INSTALL SHOWER HEAD

TEFLON TAPE

Rap SHOWER ARM (3) threads with Teflon tape.

Tighten SHOWERHEAD (1)

with an adjustable wrench.

Do not over tighten.

INSTALL HOUSING TO SHOWER HEAD

Install HOUSING (2) onto SHOWER HEAD (1). Thread

HOUSING (2) counter-clockwise to install onto SHOWER

HEAD (1). Hand tighten only.

1

3

3

2

2

Thank you for selecting American-Standard...the benchmark

of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--

please read these instructions carefully before you begin.

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

CARE: