American Standard Monoblock Lavatory Faucet with Speed Connect Drain - Manual
American Standard Monoblock Lavatory Faucet with Speed Connect Drain – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TIGHTEN LOCKNUT
- Page 3 – Important: If SUPPLY HOSES
- Page 4 – SERVICE; CAUTION; TEST INSTALLED FITTING
- Page 5 – Speed ConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; rear; “Locked”; front; “Unlocked”; Unlocked Mode
- Page 7 – M O D E L N U M B E R; QUENTIN; M O N O B L O C K L AVAT O R Y
M 9 6 5 2 2 7
Certified to comply with ANSI A112.18.1
I n s t a l l a t i o n
I n s t r u c t i o n s
M O N O B L O C K L AVAT O R Y
F A U C E T w i t h Speed Connect™ Drain
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
7440.101
1
QUENTIN™
To ensure that your installation proceeds smoothly-please read these instructions carefully
before you begin.
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only
on American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
C O L L A R O N
M O U N T I N G N U T
8
2
4
3
1
9
1
Turn off hot and cold water
supplies before beginning.
CAUTION
G R O O V E
( FA U C E T
B A S E )
M O U N T I N G S U R FA C E
6
4
7
5
Fig.
C.
Fig.
B.
Fig.
A.
P U T T Y
I F R E Q U I R E D
INSTALL FAUCET
Installation less ESCUTCHEON PLATE:
Seat SEAL
(1)
into under side of FAUCET BASE
(2)
.
Feed FAUCET SUPPLIES
(3)
, MOUNTING STUD
(4)
and DRAIN
CABLE ASSEMBLY
(8)
through the mounting hole of lavatory or
mounting surface.
Fig. B.
Installation with ESCUTCHEON PLATE:
Apply a light bead of plumbers putty
to underside of ESCUTCHEON PLATE
(9)
if mounting surface is uneven.
Place ESCUTCHEON
PLATE
(9)
onto sink or mounting surface.
Feed FAUCET SUPPLIES
(3)
, MOUNTING
STUD
(4)
and DRAIN CABLE ASSEMBLY
(8)
through ESCUTCHEON PLATE and PUTTY
PLATE
(9)
and mounting hole of lavatory or mounting surface.
Fig. A.
From below, push GASKET
(7)
and RETAINING WASHER
(5)
onto
MOUNTING STUD
(4)
. Secure Faucet with MOUNTING NUT
(6)
,
pulling faucet to front of sink, so SUPPLIES
(3)
rests against
mounting hole. Before final tightening, make sure collar on
MOUNTING NUT
(6)
is seated into RETAINING WASHER
(5)
.
Fig. C .
Adjust Faucet so that it is centered. Tighten MOUNTING NUT
(6)
to complete faucet mounting.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M 9 6 5 2 2 7 D O W N W H I T E F O A MG A S K E TN O T V I S I B L E D R A I NF L A N G E Fig. A. Fig. B. 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCK...
M 9 6 5 2 2 7 CHECK OPERATION OF POP-UP 8 MAKE WATER SUPPLY AND WASTE CONNECTIONS 9 Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation isnow complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. Fig. A. ...
M 9 6 5 2 2 7 12 11 4 SERVICE Turn off hot and cold watersupplies before beginning. CAUTION TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3) . Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR...
