American Standard M968852 - Manual
American Standard M968852 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALL HANDLES; GROOVE; DRAIN INSTALLATION; LAVATORY; INSTALL WALL SPOUT
- Page 3 – TEST INSTALLED FAUCET; TO REMOVE; SERVICE
- Page 4 – S E R I N; WALL MOUNT; MODEL NUMBER
M968852 Rev.1.3
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
HOT
COLD
Turn off hot and cold water
supplies before beginning.
CAUTION
Installation
Instr uctions
2064.451
ROUGHING-IN DIMENSIONS
1
2" D.
(52mm)
1"
(25mm)
2" MIN.
(51mm)
3" MAX.
(76mm) MAX.
FINISHED
WALL
FINISHED
WALL
2" D.
(52mm)
9-1/4"
(235mm)
1/2" NPT INLETS
8"
(203mm)
4"
(102mm)
CROSS
HANDLE
1
INSTALL VALVE BODY
Determine where the finished wall location will be.
This measurement
is very important!
Note: The rough-in measurement from the finished
wall is; 2" minimum and 3" maximum. This is a 1" tolerance. See
rough-in illustration above.
Secure FAUCET BODY
(1)
to cross brace of wall structure
at required height using two wood screws.
Turn valves to off position. Turn hot and cold supplies on and
check fitting connections for leaks .
Complete wall construction.
WOOD SCREWS
HOT
COLD
CROSS BRACE
WALL STUDS
16"
MAXW
AL
L
M
IN
1-5
/8"D
EEP
MAXW
AL
L
M
IN
1-5
/8"D
EEP
Connect HOT water supply to left VALVE inlet and COLD water
supply to right VALVE inlet. Use pipe sealant or Teflon tape for
all threaded connections. For sweat connections, do not make
sweat connections directly to valve body. Damage to seals and
and valve cartridge may occur.
Required Tools
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
2-1/8" D.
(54mm)
2" MAX.
(51mm) MAX.
1-1/4" O.D.
(32mm) O.D.
Pipe Wrench
Teflon Tape
Plumbers' Putty or
Caulking
Tubing Cutter
W A L L M O U N T F A U C E T
I N - W A L L L AVAT O R Y F I T T I N G
SERIN
™
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M968852 Rev.1.3 4 3 INSTALL HANDLES GROOVE GROOVE FINISHED WALL 1 1 4 8 9 5 6 7 4 2 DRAIN INSTALLATION Assembly GASKET (2) WASHER (3) and LOCKNUT (4) onto DRAIN BODY (1) . Tighten LOCKNUT (4) firmly. Assembly TAILPIECE (5) to DRAIN BODY (1) . Apply a bead of PUTTY to underside of FLANGE on DRAIN BOD...
M968852 Rev.1.3 6 TEST INSTALLED FAUCET 7 Turn HANDLES to "off" position. Remove AERATOR (1) using TOOL (2) supplied. Check all drain connections for leaks. Turn handles to OFF position. Replace AERATOR (1) . Turn hot and cold water supplies on. Operate both HANDLES to flush water lines thor...
M968852 Rev.1.3 S E R I N ™ WALL MOUNT LAVATORY FAUCET MODEL NUMBER M950245-YYY0A HANDLE ASSEMBLY M962424-YYY0A HANDLE ESCUTCHEON KIT M962422-YYY0A SPOUT ASSEMBLY M962757-0070A AERATOR 015025-YYY0A DRAIN COMPLETE 070532-0040A TAILPIECE M962423-YYY0A SPOUT ESCUTCHEON KIT 918555-0070A HANDLE SCREW 617...
