American Standard M66240 - Manual
American Standard M66240 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Certified to comply with ASME A112.18.1M
I n s t a l l a t i o n
I n s t r u c t i o n s
T M
0
1
2
3
4
5
6
K I T C H E N FA U C E T S
2 0 2 1 . 6 X X
FAUCET INSTALLATION (ESCUTCHEON OPTIONAL)
Insert supply TUBES
(1)
and threaded MOUNTING STUD
(2)
through center hole of ESCUTCHEON
(3)
and sink deck, or selected
sink hole if ESCUTCHEON
(3)
is not used.
Make sure black RUBBER GASKET
(4)
is properly centered on base.
Orient faucet so that threaded STUD
(2)
is centrally located towards
rear of sink, then assemble RETAINER PLATE with GASKET
(5)
, or
MOUNTING KIT
(5a)
and thread LOCKNUT
(6, 6a)
onto MOUNTING
STUD
(2)
from underside of sink.
Hand tighten LOCKNUT
(6, 6a)
and check that rotation of HANDLE
(7)
from HOT to COLD is centered. Secure faucet by tightening LOCKNUT
(6, 6a)
firmly. Spread TUBES
(1)
for better access to LOCKNUT
(6, 6a)
.
If using ESCUTCHEON
(3)
, thread ESCUTCHEON WING NUTS
(8)
onto
studs from underside of sink and hand-tighten.
2
M 6 6 2 4 0 R E V. 1 . 1
Peel off paper backing from WASHER
(1, 1a)
and stick WASHER
(1, 1a)
into circular groove of the SUPPORT PLATE
(2, 2a)
.
REAR EDGE
4
4
6
5
3
3a
3a
INSTALL
Place SUPPORT PLATE
(2, 2a)
in
center of ESCUTCHEON
(3, 3a)
with WASHER
(1)
visible.
Turn ESCUTCHEON
(3, 3a)
over
with notch of SUPPORT
PLATE
(2, 2a)
towards rear of
sink, align STUDS
(4)
with
outer holes of sink and
place ESCUTCHEON
(3, 3a)
onto
deck. Hole of SUPPORT
PLATE
(2, 2a)
must align with
hole of sink.
FOR MODEL 2021.631 ONLY:
Install ESCUTCHEON
(3a)
(as described on the left).
Insert SPRAY HOLDER
(5)
through side hole of installed
ESCUTCHEON
(3a)
, thread WING NUT
(6)
to shank of SPRAY
HOLDER
(5)
from underside of sink. Center SPRAY HOLDER
(5)
on ESCUTCHEON
(3a)
and secure by tightening WINGNUT
(6)
.
1
1
1
2
2
3
2a
Install ESCUTCHEON (optional)
REAR EDGE
INSTALL
1
5
5a
5
8
6
6
6a
6a
4
4
7
LOCKNUT
(FAUCETS
LESS SPRAY)
MOUNTING KIT
FOR FTG. WITH
HAND SPRAY
LOCKNUT
LESS ESCUTCHEON
TOOLS REQUIRED
Phillips Screwdriver
Plumbers' Putty or Caulking
Adjustable Wrench
Channel Locks
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Turn off water at
main supply.
CAUTION
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
