American Standard 9210.224.329 - Manual

ASSEMBLY & INSTALLATION INSTRUCTIONS

- 1 -

- 2 -

In the United States:

American Standard Inc.

P.O. Box 6820

Piscataway, New Jersey 08855

Attention: Director of Consumer Affairs

For residents of the United States, warranty information

may also be obtained by calling the following

toll free number: (800) 442-1902

www.americanstandard-us.com

In Canada:

American Standard

2480 Stanfield Rd.

Mississauga, Ontario

Canada L4Y 1S2

Toll Free: (800) 387-0369

www.americanstandard.ca

In Mexico:

Customer Service Manager

Ideal Standard, S.A. de C.V.

Via Morelos #330

Col. Santa Clara

Ecatepec 55540 Edo. Mexico

www.americanstandard.com.mx

Recommended Tools & Materials

Roughing-in Dimensions

Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2008

Hacksaw

Channel Locks

Adjustable Wrench

Tubing Cutter

Basin Wrench

Putty Knife

Tape
Measure

Plumbers’ Putty or
Caulking

Regular Screwdriver

Phillips Screwdriver

Drill

Level

Pipe Wrench

Generations 24" Washstand
9210.224.329

7 7 0 0 0 2 - 1 0 0

7 7 0 0 0 2 - 1 0 0

7 7 0 0 0 2 - 1 0 0

7 7 0 0 0 2 - 1 0 0

WASHSTAND INSTALLATION

Unpack unit carefully, taking care that bottom shelf does not drop and damage front legs (

see Figure 2

).

Provide suitable reinforcement for anchoring the washstand to the wall. Centerline of reinforcement should be 27-3/4"

up from the floor (

see Figure 1

).

Rough in supply lines and waste per rough-in dimensions.

The molding needs to be notched to seat the washstand flush against the wall.

Move the washstand into place and level with the adjustable glides on the bottom of the feet.

The glides can be adjusted outward up to 1" but it is recommended not to exceed 1/2" if possible.

Drill at least two 3/8" O.D. anchoring holes through the centerline of the rear stringer of the vessel stand, located 3/4"

down from the top of the table (

see Figure 2

).

Anchor the washstand to the wall through at least 2 of the anchoring holes in the rear of the washstand (

see Figure 2

).

Continue with installation appropriate for top and sink options chosen.

AMERICAN-STANDARD WOOD FURNITURE WARRANTY

If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is defective in
materials or workmanship, American-Standard will repair or, at its option, exchange the product for a similar model. Variations in
actual wood color and finishes which may result from natural characteristics of the wood, such as grain patterns, mineral streaks
and the like, are not defects and are not covered by this warranty.
This warranty applies only to the original purchaser and installation of these products.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the
purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before
installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty
maintenance, abuse, misuse, accident or other damages; if it was not installed in accordance with American-Standard’s
instructions; or if it has been modified in a manner inconsistent with the product as shipped by American-Standard.
American-Standard’s option to repair or exchange the product under this warranty does not cover any labor or other costs of
removal or installation, nor shall American-Standard be responsible for any other incidental or consequential damages
attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this
warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not
apply to you).
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or province to
province, in which case this warranty does not affect such statutory rights.

C/L of 2 x 6

Reinforcement

Finished

Floor

27-3/4"

(705mm)

FIGURE 1

- 4 -

REPLACEMENT PARTS LIST

9210.224.329 Generations 24" Washstand

ADJUSTABLE

LEVELLERS

(under each foot)

- 3 -

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin.
Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading.
Also avoid extreme changes in temperature by arranging furniture away from radiators, heat and air vents,
and air conditioning units. Avoid placing furniture directly under windows.

22-1/2"

(570mm)

18"

(457mm)

33"

(838mm)

14-1/8"

(359mm)

16"

(406mm)

18"

(457mm)

TOWNSEND

SINK

SUPPLIES AS

REQUIRED

FINISHED

FLOOR

FINISHED

FLOOR

FINISHED

WALL

FINISHED

FLOOR

FINISHED

WALL

REAR STRINGER

WITH ANCHORING

HOLES TO SECURE

VANITY TO WALL

Care and Cleaning of Vanity

Clean the product by using soft, slightly damp cloth. Buff the product by using a soft dry cloth. Avoid using silicone cleaners and waxes.

Clean up excess water and spills immediately. Use a blotting rather than a wiping action. Water left over a long period of time will cause white

spots in the finish.

NOTE: Please note that some chemicals may damage the finish. Take care to avoid the following: iodine, hair dye, after shave lotion, shaving

cream, alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray Disinfectant®, Dow Disinfectant®, acetone, paint remover, Formula

409®, Tile-X®, and Nair®.

REPAIR PART NO.

DESCRIPTION

THREADER LEVELER (1 PER PACK) FOR WASHSTAND

730679-0070A

VANITY TOP

No top required for
Townsend Vanity Top (sink)

0555.104 Townsend Vanity Top (4" centers)
0555.108 Townsend Vanity Top (8" centers)

7005.201 Copeland Center Spread
7005.801 Copeland Wide Spread

RECOMMENDED SINKS

RECOMMENDED FAUCETS

1-1/4" O.D.

WASTE

FIGURE 2

ANCHORING
HOLES
IN REAR
STRINGER
[NOT SHOWN]

TOWNSEND VANITY TOP 0555.104/0555.108
INSTALLATION onto WASHSTAND…

Two people recommended for this installation

Mount the drain assembly (not included) on the sink. Be certain to apply
a bead of sealing putty on the underside of the drain (Part "A") in order to ensure
a watertight seal between the sink and drain. Remove excess putty after installing
the drain on the sink.
Apply a bead of silicone adhesive to the rim of the vanity. Place the top centered
left to right on the vanity and with the back edge of the top even with the rear of
the vanity. Apply a bead of silicone along the top back edge of the vanity top
and the wall. Clean up any excess silicone.

Connect the trap to the drain assembly hand tight to check alignment. It may be necessary
to cut off part of the tailpiece (area "B") or part horizontal leg of the trap (area "C").

Connect hot and cold supply lines to the shut off valves.
Tighten trap joints for watertight assembly.

A

B

C

Drawer pulls

out to access

Storage

Townsend Sink

Open Storage

33"

(838mm)

8"

(203mm)

2-1/2"

(64mm)

4"

(102mm)