American Standard 8871 - Manual
American Standard 8871 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – HOT
- Page 4 – CAUTION
- Page 5 – Speed ConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; rear; “Locked”; front; “Unlocked”; Unlocked Mode
8 8 7 1
4
6
2
5
SLOT
MOUNTING
SURFACE
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT
(1)
and CABLE CONNECTOR
(2)
through center hole, making sure
the SPOUT SEAL WASHER
(3)
is properly seated.
Assemble RUBBER WASHER
(4)
, BRASS WASHER
(5)
and LOCKNUT
(6)
onto SPOUT
SHANK
(7)
from under side of sink . Make sure SPOUT
(1)
is centered in the mounting
hole and the
slot
in the BRASS WASHER
(5)
faces toward the rear of the sink.
Tighten LOCKNUT
(6)
firmly.
Fig. A.
Tighten LOCKNUT
(11)
with WRENCH
(8)
(supplied) to secure VALVE
BODY
(13)
. Repeat above steps for opposite VALVE BODY
(13A)
.
Install LOCKNUT
(11)
and RUBBER WASHER
(12)
onto VALVE BODY
(13)
.
From under side of mounting surface, install VALVE BODY
(13)
through valve
mounting holes. Threads of VALVE BODY
(13)
should extent at least 5/16
of a inch above mounting surface top.
Fig. B.
Thread DECK ADAPTER
(10)
onto VALVE BODY
(13)
until snug against internal stop. If necessary, adjust
LOCKNUT
(11)
.
1
1A
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
INSTALL SPOUT
INSTALL VALVE BODY
1
8
10
9
12
11
13
13a
10
9
12
11
3
Place RUBBER RING
(9)
into DECK ADAPTER
(10)
.
13
5/16'' MIN.
7
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
Tubing Cutter
Fig.
A.
Fig.
B.
1
L E X I N G T O N S p r e a d L a v a t o r y
F a u c e t
with the Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet
with the Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
1
M966230 Rev. 1.2
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation isnow complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. Fig. A. ATTACH CABLE CONNECTOR 7 2 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens ...
DO: SIMPLY RINSE THE PRODUCTCLEAN WITH CLEAR WATER. DRYWITH A SOFT COTTON FLANNELCLOTH. DO NOT: DO NOT CLEAN THEPRODUCT WITH SOAPS, ACID,POLISH, ABRASIVES, HARSHCLEANERS, OR A CLOTH WITHA COARSE SURFACE. CARE INSTRUCTIONS: CHECK DRAIN CONNECTIONS 11 10 12 TEST INSTALLED FITTING With VALVE (1) in OFF...
Speed Connect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use fing...
