American Standard 751711-100 - Manual

INSTALLATION INSTRUCTIONS

751711-100 REV. G

© American Standard Inc. 2007
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.

HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS

CADENZA™

WHIRLPOOL

6060.XXXWSERIES

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

T H A N K Y O U . . .

for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.

To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

List of Optional Components (not included):

• Apron Kit 0707.200*
• Tile Bead Kit 751755-100*

List of Required Components (not included):

• Drain 1583.470* • Bath Filler*

* see your American Standard Distributor

List of Required Tools and Supplies:

Tools

• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard Woodworking Tools
• Personal Safety Equipment
• Caulking Gun

Supplies

• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2 Stringers
• Drop Cloth
• 20 amp GFI Outlet
• Cement, Plaster, Grout

1949mm

(76-3/4 REF.)

546mm

(21-1/2)

ROUGH FLOOR

495mm

(19-1/2)

1384mm

(54-1/2)

1605mm

(63-3/16)

975mm

(38-3/8)

1661mm

(65-3/8)

346mm

(13-5/8)

SEAT AREA

254mm

(10)

114mm

(4-1/2)

PROVIDE ACCESS TO PUMP FOR SERVICE

ON ALL INSTALLATIONS

NOTE: APRON ASSEMBLY WILL PROVIDE REQUIRED

ACCESS FOR SERVICING

51mm
(2)

89mm

(3-1/2)

C/L OF OVERFLOW

LEVELING STRINGER
NOT FOR SUPPORT

PUMP

178mm x 381mm

(7 x 15) CUTOUT

C/L OF

DRAIN

143mm

(5-5/8)

OUTLINE OF

CUTOUT

C/L

ON/OFF SWITCH

83mm

(3-1/4)

1-1/2 N.P.T. THREAD

1-1/2 O.D. TAILPIECE

38mm

(1-1/2)

INTEGRAL FEET
SUPPORT

RECOMMENDED FITTING
LOCATION 64 X 381mm (2-1/2 X 15)

E-Z-Install™ HEATER

I N S T A L L E D S I Z E
W E I G H T
W E I G H T w / W A T E R
G A L . T O O V E R F L O W
W H I R L P O O L M I N . O P E R A T I N G V O L .
B A T H I N G W E L L A T S U M P
B A T H I N G W E L L A T R I M
W A T E R D E P T H T O O V E R F L O W
F L O O R L O A D I N G
( P R O J E C T E D A R E A )
P T S .

C U B E ( F T

3

)

GENERAL SPECIFICATIONS FOR 6060 WHIRLPOOL

WHIRLPOOL ELECTRICAL SPECIFICATIONS

S Y S T E M I I P U M P

7 6 - 3 / 4 x 6 5 - 3 / 8 x 2 1 - 1 / 2 I n . ( 1 9 4 9 x 1 6 6 1 x 5 4 6 m m )

1 0 5 L b s . ( 4 8 K g . )

8 2 2 L b s . ( 3 7 0 K g . )

8 6 G a l . ( 3 2 6 L )
7 1 G a l . ( 2 6 9 L )

4 5 x 4 0 I n . ( 1 1 4 3 x 1 0 1 6 m m )
4 9 x 4 3 I n . ( 1 2 4 5 x 1 0 9 2 m m )

1 5 - 3 / 8 I n . ( 3 9 1 m m )

2 4 L b s . / S q . F t . ( 1 1 4 K g s . / S q . m )

4 1 . 7
6 8 . 4

2 . 1 H P , 1 5 . 6 A M P S , 1 2 0 V .