American Standard 7420.821 - Manual
American Standard 7420.821 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – MAKE WATER SUPPLY AND WASTE CONNECTIONS; HOT
- Page 5 – Speed ConnectTM Drain; Troubleshooting Guide; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; “Locked”; Locked Mode
- Page 7 – P O R T S M O U T H TM; S p r e a d L a v a t o r y F a u c e t; Series
M 9 6 5 01 5 R E V. 1. 7
Certified to comply with ANSI A112.18.1
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
Tubing Cutter
1
2
1
3
4
6
12
5
SLOT
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT
(1)
and CABLE CONNECTOR
(12)
through center hole, making sure
the SEAL WASHER
(3)
is properly seated in the SPOUT ESCUTCHEON
(2)
.
Assemble RUBBER WASHER
(4)
, BRASS WASHER
(5)
and LOCKNUT
(6)
onto SPOUT
SHANK
(7)
from under side of sink . Make sure SPOUT
(1)
is centered in the mounting
hole and the
slot
in the BRASS WASHER
(5)
faces toward the rear of the sink.
Tighten LOCKNUT
(6)
firmly.
Fig. A.
1
1A
INSTALL SPOUT
INSTALL VALVE BODY
1
8
11
7
Fig.
A.
MOUNTING
SURFACE
Hand tighten LOCKNUT
(11)
to secure VALVE BODY
(8)
.
Repeat above steps for opposite VALVE BODY
(8A)
.
Install LOCKNUT
(11)
onto VALVE BODY
(8)
.
From under side of mounting surface, install VALVE BODY
(8)
through valve
mounting holes. Threads of VALVE BODY
(8)
should extent at least 5/16
of a inch above mounting surface top.
Fig. B.
Thread ADAPTER
(10)
onto VALVE BODY
(8)
until snug against internal stop. If necessary, adjust
LOCKNUT
(11)
.
8
11
Place RUBBER RING
(9)
into ADAPTER
(10)
.
5/16'' MIN.
8A
Fig.
B.
7420.801
7420.821
Series
7415.801
7415.821
Series
Installation
Instr uctions
P O R T S M O U T H ™
S p r e a d L a v a t o r y F a u c e t
with Speed Connect™ Drain
10
9
10
9
Congratulations on purchasing your
American Standard faucet with
Speed Connect drain, a feature found
onlyon American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully
before you begin.
74 2 0
74 1 5
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. Thread TEE BODY (4) to SPOUT SHANK (5) . Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7...
Fig. F. 5 Speed Connect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B...
LOOP TOWARD REAR OF SINK LOOP TOWARD FRONT OF SINK Fig. G. 180˚ LOGO LOGO DRAIN Fig. H. STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert th...
