American Standard 7420.101 - Manual
American Standard 7420.101 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Note: If additional supply length is required, installer must
- Page 4 – SERVICE; CAUTION; TEST INSTALLED FITTING; CONVERT TO A FIXED SPOUT IF DESIRED.; SPOUT CAN BE FIXED OR SWIVEL.
- Page 5 – Speed ConnectTM Drain; Troubleshooting Guide; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; “Locked”; Unlocked Mode
- Page 7 – MODEL NUMBERS; P O R T S M O U T H TM; appropriate finish code; M o m o b l o c k L a v a t o r y F a u c e t
M 9 6 5 0 1 6 R E V. 1 . 6
7 4 1 5 . 1 0 1
7 4 2 0 . 1 0 1
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
M O N O B L O C K L AVAT O R Y
FA U C E T w i t h Speed Connect™ Drain
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
7420.101
7415.101
Series
1
PORTSMOUTH™
To ensure that your installation proceeds smoothly-please read these instructions carefully
before you begin.
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only
on American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
COLLAR ON
MOUNTING NUT
8
2
4
3
1
1
8
1
INSTALL FAUCET
7420.101 & 7415.101
Turn off hot and cold water
supplies before beginning.
CAUTION
GROOVE
(FAUCET
BASE)
MOUNTING SURFACE
6
4
7
5
Installation less ESCUTCHEON PLATE:
Seat SEAL
(1)
into under side of FAUCET BASE
(2)
.
Feed FAUCET SUPPLIES
(3)
, MOUNTING STUD
(4)
and DRAIN
CABLE ASSEMBLY
(8)
through the mounting hole of lavatory or
mounting surface.
Fig. B.
From below, push GASKET
(7)
and RETAINING WASHER
(5)
onto
MOUNTING STUD
(4)
. Secure Faucet with MOUNTING NUT
(6)
,
pulling faucet to front of sink, so SUPPLIES
(3)
rests against
mounting hole. Before final tightening, make sure collar on
MOUNTING NUT
(6)
is seated into RETAINING WASHER
(5)
.
Fig. C .
Adjust Faucet so that it is centered. Tighten MOUNTING NUT
(6)
to complete faucet mounting.
Fig.
C.
Fig.
B.
Fig.
A.
Installation with ESCUTCHEON PLATE:
Apply a light bead of plumbers putty
to underside of ESCUTCHEON PLATE
(8)
if mounting surface is uneven.
Place ESCUTCHEON
PLATE
(8)
onto sink or mounting surface.
Feed FAUCET SUPPLIES
(3)
, MOUNTING
STUD
(4)
and DRAIN CABLE ASSEMBLY
(8)
through ESCUTCHEON PLATE
(8)
and
mounting hole of lavatory or mounting surface.
Fig. A.
PUTTY
IF REQUIRED
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CHECK OPERATION OF POP-UP 8 MAKE WATER SUPPLY AND WASTE CONNECTIONS 9 Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. Fig. A. ATTACH CABLE ...
12 11 4 2 8 2.5mm HEX KEY 5 6 3 4 7 REMOVE INSTALL SERVICE To remove or replace cartidge: Fig. A. Turn valve to OFF position. Remove HANDLE SCREW (2) . Pull off HANDLE (3) and CAP (4) . Unthread CARTRIDGE NUT (5) and remove. Pull out CARTEIDGE (6) . Inspect CARTRIDGE (6) and O-RING (7) for debris an...
Speed Connect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use fing...
