American Standard 7411.722 - Manual
American Standard 7411.722 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – HOT
- Page 4 – EverCleanTM Finish Care Instructions
- Page 5 – SpeedConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; “Locked”; Unlocked Mode
U S 6 0 4 0 2 R e v . 1 . 1
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
C e n t e r s e t L a v a t o r y F a u c e t w i t h
EverClean™ Finish & SpeedConnect™ Drain
Adjustable Wrench
Screwdriver
Channel Locks
Required tools
Tubing Cutter
1
INSTALL FAUCET
SINK OR
MOUNTING
SURFACE
POP-UP
CABLE
Turn off hot and cold water supplies before beginning.
Insert FAUCET
(1)
and CABLE CONNECTOR
(2)
through
mounting holes of Sink or mounting surface.
Fig. A.
Assemble LOCKNUTS
(3)
onto SHANKS
(4)
from under
side of Sink. Hand tighten firmly.
Fig. B.
2
2
4
3
3
4
Turn off hot and cold water
supplies before beginning.
CAUTION
(HAND TIGHTEN)
Congratulations on purchasing your American Standard faucet with
EverClean finish and SpeedConnect drain, two features found only
on American Standard faucets.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
*Your new American Standard faucet is designed to work only with the SpeedConnect drain. Heplful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Fig. A.
Fig. B.
7411.702
7411.712
7411.722
7411.732
1
SpeedConnect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
COMPRESSION NUT 3/8” COMPRESSION CONNECTION COUPLING NUT FLEXIBLE SUPPLIES 3/8 O.D. BULL-NOSE RISERS Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. CHECK OPERA...
2 1 4 1 SERVICE 10 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3) . Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3) . 5 2 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fil...
SpeedConnect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use finge...
