American Standard 7048 Series - Manual

American Standard 7048 Series

American Standard 7048 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
Page: / 4

Table of Contents:

  • Page 2 – TOP; SINK INSTALLATION; SINK UPSIDE DOWN; SINK CUTOUT
  • Page 3 – INSTALLED VIEW (after completing steps 2 thru 7); TOP VIEW
  • Page 4 – AMERICAN STANDARD TEN-YEAR LIMITED WARRANTY; Corian; Cleaning
Loading the manual

C H A N D L E R ™ A P R O N K I T C H E N S I N K

M O D E L 7 0 4 8 S E R I E S

I n s t a l l a t i o n
I n s t r u c t i o n s

7 9 0 7 5 9 - 1 0 0 R E V A

Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.

BEFORE YOU BEGIN...Unpack new sink and inspect carefully for damage. Replace the sink in its original
packing carton to protect it until you are ready to begin installation.

Certified to comply with ANSI Z124.6
Patent Pending
Observe local plumbing and building codes.

RECOMMENDED TOOLS & MATERIALS

Putty Knife
Pipe Wrench
Channel Locks
Drill

Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Basin Wrench

Saber Saw
Plumbers' Putty or
Caulking
Various Carpentry Tools

Tubing Cutter
Tape Measure
Hacksaw
Silicone Adhesive

M

A D E W I T H

Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.

Corian

®

Dupont registered trademark

© American Standard Inc. 2004

PRODUCT REQUIREMENTS
Due to the special nature of this installation, American Standard recommends that an experienced cabinet
maker build the new cabinet or modify an existing cabinet to achieve a satisfactory installation.
To ensure proper fit of the sink in the cabinet, we suggest you provide the cabinet maker with the actual sink
that will be installed.

NOTES
The cabinet designs illustrated below are intended as suggestions only. Your specific installation requirements
may vary from those shown.

SINK DIMENSIONS

NOTE: Tile recess is
designed to accept four
6" x 6" x 5/16" thick tiles
(by others). Secure tiles
with silicone adhesive.

3 / 8
( 1 0 m m )

2
( 5 1 m m )

6 - 3 / 1 6

( 1 5 7 m m )

9 - 3 / 4

( 2 4 8 m m )

S E A L I N G
C O M P O U N D

F R O N T O F

C A B I N E T

2 4 - 1 / 2

( 6 2 2 m m )

T I L E R E C E S S

3 3 ( 8 3 8 m m )

7 - 1 / 8

( 1 8 1 m m )

3 - 1 / 2
( 8 9 m m ) D I A .

1 - 3 / 8 ( 3 5 m m ) D I A .

H O L E S T Y P .

8 - 3 / 4

( 2 2 2 m m )

2 2

( 5 5 8 m m )

C / L

7 0 4 8 . 8 0 4
4 H O L E
V A R I A T I O N

1 - 3 / 4
( 4 4 m m ) D I A .

1 - 1 / 2
( 3 8 m m ) R E F .

3 6

( 9 1 4 m m )

4 - 1 / 2

( 1 1 4 m m )

9 - 1 / 2

( 2 4 1 m m )

1 ( 2 5 m m )
R A D . T Y P .

CABINET DESIGN
The sink is designed to be installed with the apron exposed and the back of the apron flush against the front of
the cabinet.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - TOP; SINK INSTALLATION; SINK UPSIDE DOWN; SINK CUTOUT

7 9 0 7 5 9 - 1 0 0 R E V A 2 COUNTERTOP TRACED LINEOF SINK 3/8 IN. MAX. 25mm (1")COUNTERTOPOVERHANG-DIM "X" CABINET FACE SINK CUTOUT LINE 1a 1 ALIGN MARKS CENTER OF MOUNTINGLOCATION MARKED ONCOUNTERTOP CENTER MARK ONBACKSIDE OF SINK SIDE VIEW COUNTERTOP CABINETFACE SHOULD BEMAXIMUM 25mm...

Page 3 - INSTALLED VIEW (after completing steps 2 thru 7); TOP VIEW

7 9 0 7 5 9 - 1 0 0 R E V A 3 1b 1C TRACED LINEOF SINK MAX. 25mm (1")COUNTERTOPOVERHANG-DIM "X" CABINET FACE CABINET FACE CUTOUT FOLLOW THE SINK CUTOUT LINE VERTICALLY DOWN ON THE CABINET SINK CUTOUT LINE COUNTERTOP NOTCHAND CABINET CUTOUT INSTALLED VIEW (after completing steps 2 thru 7)...

Page 4 - AMERICAN STANDARD TEN-YEAR LIMITED WARRANTY; Corian; Cleaning

A B Double Bowl Trap 3 4 6 7 Connect supply lines tofaucet finger tight, andcarefully bend to engage with the supply stops.Tighten connections tofaucet for secure seal. 5 Connect drain assemblyhand tight to check alignment. It may benecessary to cut off partof the tailpiece (area "A") or par...

Other American Standard Models

All American Standard Other