American Standard 7048.401 - Manual
American Standard 7048.401 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Perimeter
of sink
Cutout
Perimeter
of sink
Cutout
C H A N D L E R ™ K I T C H E N S I N K
w / D R A I N B O A R D
M O D E L 7 0 4 8 . 4 0 1 R I G H T H A N D D R A I N B O A R D
M O D E L 7 0 4 8 . 5 0 1 L E F T H A N D D R A I N B O A R D
I n s t a l l a t i o n I n s t r u c t i o n s
7 9 0 7 6 0 - 1 0 0
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
1
2
B E F O R E Y O U B E G I N . . . Unpack new sink and
inspect carefully for damage. Replace the sink
in its original packing carton to protect it until
you are ready to begin installation.
3
Drill a clearance
hole inside the
cutout line
as marked on
the countertop.
NOTE: The drain-
board is not
part of the cut
out and sits above the countertop.
Mount the faucet
and drain assembly
on the sink
following the
manufacturer's
instructions.
Cut opening on
cut line inside the
perimeter of bowl
shape.
AFTER THE CUTOUT IS DRAWN...
Certified to comply with ANSI Z124.6
Observe local plumbing and building codes.
™
C U T O U T D I M E N S I O N S F O R S I N K
Recommended Tools & Materials
Putty Knife
Pipe Wrench
Channel Locks
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Drill
Locate and mark center lines of sink on countertop.
Provide proper clearance under the countertop for
the faucet supply lines and the structural parts of the
cabinet.
By using the diagram below and measuring your sink,
draw the outline of the sink onto the countertop. This
is not the cutting outline.
Basin Wrench
Saber Saw
Plumbers' Putty or
Caulking
Tubing Cutter
Tape Measure
Hacksaw
M
A D E W I T H
3 2 "
1 9 - 1 / 2 "
1 9 - 1 / 2 "
2 1 "
1 0 - 1 / 2 "
2 1 " R
a d i u s
2 1 " R
a d i u s
3 5 "
1 - 1 / 2 "
C E N T E R L I N E
S I N K
O U T L I N E
R I G H T
H A N D
D R A I N
B O A R D
C / L O F
D O U B L E
B O W L
1 / 2 " T Y P .
C U T T I N G
L I N E
( S H A D E D
A R E A )
C U T T I N G
L I N E
C U T O U T F O R N E W I N S T A L L A T I O N
M O D I F I C A T I O N R E Q U I R E D T O F I T C H A N D L E R S I N K
I N T O A S T A N D A R D 3 3 " X 2 2 " S I N K C U T O U T
N O T E :
A L L O W R O O M O N E I T H E R S I D E O F S I N K
D E P E N D I N G O N R I G H T O R L E F T H A N D D R A I N B O A R D
1 0 - 1 / 2 "
2 1 "
2 2 "
4 9 - 1 / 2 "
3 5 "
3 2 "
Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.
Corian
®
Dupont registered trademark
© American Standard Inc. 2000
R i g h t H a n d
D r a i n B o a r d
L e f t H a n d
D r a i n B o a r d
Right Hand Shown
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
