American Standard 7038 - Manual
American Standard 7038 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – MAKE WATER SUPPLY AND WASTE CONNECTIONS; HOT
- Page 5 – Speed ConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; rear; “Locked”; front; “Unlocked”; Locked Mode
- Page 7 – TIPS FOR REMOVING YOUR OLD DRAIN:; Remove Drain Body from below sink.; WHEN DRAIN IS REMOVED FROM ABOVE SINK; disassembled from the sink.; For Drains that are removed from below Sink:
M 9 6 8 8 6 8 R e v 1 . 2
7038
Certified to comply with ANSI A112.18.1
Installation
Instructions
T R I U M P H
W i d e s p r e a d L a v a t o r y F a u c e t
with
Speed Connect™ Drain
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
Tubing Cutter
1
2
1
3
4
6
12
5
SLOT
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT
(1)
and CABLE CONNECTOR
(12)
through center hole, making sure
the SPOUT ESCUTCHEON
(2)
and SEAL WASHER
(3)
are properly seated.
Assemble RUBBER WASHER
(4)
, BRASS WASHER
(5)
and LOCKNUT
(6)
onto SPOUT
SHANK
(7)
from under side of sink . Make sure SPOUT
(1)
is centered in the mounting
hole and the
slot
in the BRASS WASHER
(5)
faces toward the rear of the sink.
Tighten LOCKNUT
(6)
firmly.
Fig. A.
1
1A
INSTALL SPOUT
INSTALL VALVE BODY
1
10
9
8
11
7
Fig.
A.
MOUNTING
SURFACE
Hand tighten LOCKNUT
(11)
to secure VALVE BODY
(8)
.
Repeat above steps for opposite VALVE BODY
(8A)
.
Install LOCKNUT
(11)
onto VALVE BODY
(8)
.
From under side of mounting surface, install VALVE BODY
(8)
through valve
mounting holes. Threads of VALVE BODY
(8)
should extent at least 5/16
of a inch above mounting surface top.
Fig. B.
Thread ESCUTCHEON
(10)
onto VALVE BODY
(8)
until snug against internal stop. If necessary, adjust
LOCKNUT
(11)
.
10
9
8
11
Place RUBBER RING
(9)
into SCUTCHEON
(10)
.
5/16'' MIN.
8A
Fig.
B.
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M 9 6 8 8 6 8 R e v 1 . 2 Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. Thread TEE BODY (4) to SPOUT SHANK (5) . Thread HOSE CONNECTOR (6, 6A)...
M 9 6 8 8 6 8 R e v 1 . 2 Speed Connect™ Drain Troubleshooting Guide 1 2 Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the ...
M 9 6 8 8 6 8 R e v 1 . 2 LOOP TOWARDREAR OF SINK LOOP TOWARDFRONT OF SINK Fig. G. 180˚ LOGO LOGO DRAIN Fig. H. STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in ...
