American Standard 7038.400 - Manual
American Standard 7038.400 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – FLANGE GASKET
- Page 4 – INSTALL HANDLES; SERVICE
- Page 5 – SpeedConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; “Locked”; Locked Mode
- Page 7 – B i d e t F a u c e t a n d Va c u u m B r e a k e r; CAUTION; BIDET FAUCET INSTALLATION; R o u g h i n g - i n D i m e n s i o n s; SPRAY INSTALLATION; EverClean Finish; T R O P I C
3
5
4
4
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
B i d e t F a u c e t a n d Tr a n s f e r Va l v e
with
EverClean™ Finish & SpeedConnect™ Drain
Congratulations on purchasing your American Standard
faucet with EverClean finish and Speed Connect drain, two
features found only on American Standard faucets.
*Your new American Standard faucet is designed to work only with the SpeedConnect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Turn off hot and cold water
supplies before beginning.
CAUTION
1
BIDET FAUCET INSTALLATION
Replace UPPER GASKET
(8)
and WASHER
(7)
and
ESCUTCHEON
(6)
until it locks against internal stop.
Position the side threaded outlet rearward and
secure MOUNTING NUT
(11)
.
Remove ESCUTCHEON
(6)
, WASHER
(7)
and
UPPER GASKET
(8)
from TRANSFER VALVE
(9).
Insert TRANSFER VALVE
(9)
into the center forward
hole of BIDET.
COLD
HOT
BIDET
LEDGE
10
3a
3
8
9
1
5
2
6
R o u g h i n g - i n
D i m e n s i o n s
SPRAY INSTALLATION
2
Assemble SPRAY BODY
(1)
to BIDET. Using putty, seal underside
of SPRAY BODY FLANGE
(2)
and secure with NUT
(3)
.
Thread SPRAY CAP
(9)
onto SPRAY BODY
(1)
.
Thread SPRAY HOSE
(4)
with SEAL WASHER
(5)
to SPRAY BODY
(1)
.
Connect other end of HOSE
(4)
with SEAL WASHER
(6)
to side outlet
NIPPLE
(7)
of the TRANSFER VALVE
(8)
.
PUTTY
6
2
7
8
1
9
Tighten LOCKNUTS
(1)
with WRENCH
(5)
(supplied)
to secure VALVE BODIES
(3, 3a)
.
Install LOCKNUT
(1)
and RUBBER WASHER
(2)
onto VALVE BODIES
(3, 3a)
. From
under side of mounting surface, install VALVE BODY
(3, 3a)
through valve mounting
holes. Threads of VALVE BODY
(3, 3a)
should extent at least 5/16 of a inch above
mounting surface top.
Fig. A.
Thread DECK ADAPTER
(4)
onto VALVE BODIES
(3, 3a)
until snug against internal stop. If necessary, adjust LOCKNUT
(1)
.
Place RUBBER RING
(10)
into DECK ADAPTER
(4)
.
MOUNTING
SURFACE
4
10
2
1
3, 3a
5/16''
MIN.
Fig. A.
11
Adjustable Wrench
Screwdriver
Channel Locks
Required tools
Tubing Cutter
Phillips Screwdriver
Plumbers' Putty or
Caulking
7
1
SpeedConnect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
BIDET OUTLINE
IS SYMBOLIC
FINISHED
FLOOR
FINISHED
WALL
1-1/4 O.D. TAILPIECE
DOUCHE
SPRAY
2-1/8
DIA.
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
1-1/4
MAX.
1-3/16
DIA.
2-1/4
DIA.
(C)
(H)
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
8 TO 12
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
T R O P I C
M 9 6 8 8 9 3
7038.400
4
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M 9 6 8 8 9 3 POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 3 5 4 2 TIGHTEN LOCKNUT 1 REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. P...
CHECK DRAIN CONNECTIONS 12 13 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Operate both HANDLES (1) to flush water lines thoroughly. Rotate TRANSFER VALVE (5) from rim wash to spray several times to check operation. Pull up ...
M 9 6 8 8 9 3 SpeedConnect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig...
