American Standard 7010.901 - Manual
American Standard 7010.901 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – HOT; INSTALL HANDLES; To change direction of handle:; SPLINE END DOWN; insta; re
- Page 3 – HANDSHOWER INSTALLATION; NOTE; Before the bathroom is completely finished, you may; Do not solder directly to valve body.; TEST INSTALLED FAUCET
- Page 4 – MODEL NUMBER; D E C K - M O U N T B AT H F I L L E R; G R E E N T E A; HAND SHOWER
*Wrench
Certified to comply with ANSI A112.18.1M
Recommended Tools
*Supplied with Fitting
*Hex key
SPOUT RECESS
Turn off hot and cold water
supplies before beginning.
CAUTION
1
2
Assemble RUBBER WASHER
(4)
and BRASS WASHER
(5)
and
LOCKNUT
(6)
onto SPOUT SHANK
(3)
. Align SPOUT ASSEMBLY
and from underside of ledge secure SPOUT ASSEMBLY into
position with LOCKNUT
(6)
.
SPOUT ASSEMBLY
PREPARE TUBE AND TEE ASSEMBLY
4
2
3
1
3
4
1
2
4
5
Prepare TUBE and TEE ASSEMBLY
(1)
to fit center to center
VALVE (2) location
(between 6-1/2" and 12")
. If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE
(1)
so that it will not effect the compression
joint at the VALVE CONNECTION.
ADJ. 6-1/2 TO 12
6
5
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
MOUNTING
SURFACE
VALVE inlet is 3/4-inch NPT male.
NOTE
MOUNTING
SURFACE
ADJ. 6-1/2 TO 12
ROUGHING-IN DIMENSIONS
MOUNTING
SURFACE
8-1/16"
D E C K - M O U N T B AT H F I L L E R
Installation
Instr uctions
7010.900
7010.901
1-1/2 MAX.
1-1/4
MAX.
1-3/16 DIA.
3
(
H
)
(
C
)
1-1/8 DIA.
12 MAX
2-1/16
DIA.
1-1/16 DIA.
3/4-14 MALE
N.P.T. INLETS
Install RING WASHER
(1)
into SPOUT recess. Check that O-RING
(2)
on end of SPOUT SHANK
(3)
is in place. Insert SPOUT SHANK
(3)
through center hole on mounting surface.
G R E E N T E A
5-5/16"
3"
3-3/4"
10-5/8"
2-1/16"
DIA.
2-1/8"
3
M 9 6 8 5 9 5 R e v . 1 . 2
2-9/16"
Remove COUPLING NUT
(3)
and FERRULE
(4)
from each
VALVE
(2)
and slide onto TUBING
(5)
.
SPOUT
ASSEMBLY
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
7-7/8"
(200mm)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
5 SERVICE 2 4 5/16'' MIN. MOUNTINGSURFACE FOR FITTINGLESS SPRAY 11 11 10 1 3 4 Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4) into mounting holes from underside of ledge.Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is properly seated on SHANK (6) . Push ...
HANDSHOWER INSTALLATION (FOR MODEL 7010.901 ONLY) Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2) is properly seated in ESCUTCHEON (1) . Install RUBBER WASHER (3) and LOC...
028679-0070A TUBE & TEEASSEMBLY 012668-0070A SHANK KIT 030274-0070A SHANKMOUNTING KIT M911810-0070A RUBBER RING 012078-0070A VALVE COUPLING KIT M962616-YYY0A HAND SHOWER HOLDER 028699-0070A COUPLING (FOR TRANSFER) M910830-0070A STREAM STRAIGHTENER 028667-0020A HAND SHOWER HOSE 033760-0070A HAND ...
