American Standard 6726 - Manual

Certified to comply with ANSI A112.18.1
U.S. Patent No. D403,750

2 4 " T O W E L B A R & G L A S S S H E L F

M 9 6 8 2 1 8 B

6 7 2 6

1

2 4 " T O W E L B A R & G L A S S S H E L F

48 TO 68

INCHES FROM

FLOOR

2

Push INDEX BUTTONS (9) into the SUPPORT POSTS (10, 10a). See illustration.

The 24" TOWEL BAR & GLASS SHELF (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS (3) supplied.

If the 24" TOWEL BAR & GLASS SHELF (1) is to be installed on a tile or plaster wall the TILE ANCHORS (4) or DRYWALL ANCHORS(6)
and SCREWS (3) should be used.

USE MOUNTING PLATE
AS TEMPLATE

5

5

6

4

4

6

4

3

3

7

9

11

11

12

13

14

CENTER
LINE

FINISHED
WALL

SLOT IN TOWEL BAR

NOTCH IN RECESS OF SUPPORT POST

1

Regular Screwdriver

Recommended Tools

Phillips Screwdriver

Drill

10'

Tape Measure

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.

S T A N D A R D
C O L L E C T I O N

Determine desired height and location (optional) and mark a center line. For the 24" TOWEL BAR (2) mark a centerline 24" horizontally
from the first location. Using the MOUNTING PLATE (5) as a template mark the two spots for the mounting holes. Repeat for the other
MOUNTING PLATE (5). If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (4).

For the 24" TOWEL BAR & GLASS SHELF (1), Install TOWEL BAR (2) into bottom of SUPPORT POSTS (10, 10a). Align

slot

in towel bar

with

notch

in recess of support post (10, 10a) (

see Figure A

). Install the WASHER (11), GLASS SHELF (15), WASHER (11) onto SUPPORT

POSTS (10, 10a). Install and tighten SCREWS (13). See illustration.

Install the WALL ESCUTCHEON (7) on the MOUNTING PLATES (5). Place 24" TOWEL BAR & GLASS SHELF (1) onto MOUNTING
PLATES (5). Secure using SCREWS (14) and tighten.

Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.

I n s t a l l a t i o n

I n s t r u c t i o n s

48" TO 68"
(OPTIONAL)

CENTER LINE

24"

10

10a

Figure A

For installations on drywall,

use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips

screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with
the wall. Place MOUNTING PLATE (5) over DRYWALL ANCHORS

(6) and insert SCREWS (3) with #2 Phillips screwdriver. See illustration

below. Secure MOUNTING PLATE (5) to wall with SCREWS (3).

For installations on tiled walls,

If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill two

1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall. Secure
MOUNTING PLATE (5) to wall with SCREWS (3).