American Standard 6721 - Manual
American Standard 6721 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Certified to comply with ANSI A112.18.1
U.S. Patent No. D403,750
R O B E H O O K
T O W E L R I N G
T I S S U E P A P E R H O L D E R
M 9 6 8 2 1 6 C
6 7 2 1
6 7 2 9
6 7 2 3
1
ROBE HOOK, TOWEL RING and TISSUE PAPER HOLDER
MOUNTING & INSTALLATION
1
Install the WALL ESCUTCHEON (7) on the MOUNTING PLATE (5). Place the ROBE HOOK (1), TOWEL RING (2) and
TISSUE PAPER HOLDER (3) over the ESCUTCHEON (7). Secure with MOUNTING SCREW (8). Tighten fully.
Push INDEX BUTTON (9) into ROBE HOOK (1), TOWEL RING (2) and TISSUE PAPER HOLDER (3). See illustration.
The ROBE HOOK (1), TOWEL RING (2) and TISSUE PAPER HOLDER (3) work best if secured to a wall stud or cross brace within the wall,
using the SCREWS (3) supplied.
If the ROBE HOOK (1), TOWEL RING (2) and TISSUE PAPER HOLDER (3) is to be installed on a tile or plaster wall the TILE ANCHORS (4)
or DRYWALL ANCHORS (6) and SCREWS (3) should be used.
Determine desired height and location (optional) and mark a center line. Using the MOUNTING PLATE (5) as a template mark the two
mounting holes. If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).
For installations on drywall,
use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips
screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush
with the wall. Place MOUNTING PLATE (5) over DRYWALL ANCHORS
(6) and insert SCREWS (3) with #2 Phillips screwdriver.
See illustration below. Secure MOUNTING PLATE (5) to wall with SCREWS (3).
5
4
3
7
8
8
9
9
9
8
FINISHED
WALL
3
2
Regular Screwdriver
Recommended Tools
Phillips Screwdriver
Drill
10'
Tape Measure
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
S T A N D A R D
C O L L E C T I O N
For installations on tiled walls,
If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill
two 1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall.
Secure MOUNTING PLATE (5) to wall with SCREWS (3).
30 TO 72
INCHES FROM
FLOOR
USE MOUNTING PLATE
AS TEMPLATE
5
6
4
4
6
3
CENTER
LINE
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
I n s t a l l a t i o n
I n s t r u c t i o n s
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
