American Standard 4508S - Manual
American Standard 4508S – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – MAKE WATER SUPPLY AND WASTE CONNECTIONS; HOT; ATTACH CABLE CONNECTOR
- Page 4 – SERVICE
- Page 5 – Speed ConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; rear; “Locked”; front; “Unlocked”; Unlocked Mode
- Page 7 – TIPS FOR REMOVING YOUR OLD DRAIN:; Remove Drain Body from below sink.; WHEN DRAIN IS REMOVED FROM ABOVE SINK; disassembled from the sink.; For Drains that are removed from below Sink:
4
6
12
5
SLOT
MOUNTING
SURFACE
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT
(1)
and CABLE CONNECTOR
(12)
through center hole, making sure
the SPOUT ESCUTCHEON
(2)
and SEAL WASHER
(3)
are properly seated.
Assemble RUBBER WASHER
(4)
, BRASS WASHER
(5)
and LOCKNUT
(6)
onto SPOUT
SHANK
(7)
from under side of sink . Make sure SPOUT
(1)
is centered in the mounting
hole and the
slot
in the BRASS WASHER
(5)
faces toward the rear of the sink.
Tighten LOCKNUT
(6)
firmly.
Fig. A.
Hand tighten LOCKNUT
(11)
to secure VALVE BODY
(8)
. Repeat above
steps for opposite VALVE BODY
(8A)
.
Install LOCKNUT
(11)
onto VALVE BODY
(8)
. From under side of mounting
surface, install VALVE BODY
(8)
through valve mounting holes. Threads of
VALVE BODY
(8)
should extent at least 5/16 of a inch above mounting
surface top.
Fig. B.
Thread ADAPTER
(10)
onto VALVE BODY
(8)
until snug
against internal stop. If necessary, adjust LOCKNUT
(11)
.
1
1A
M 9 6 8 6 7 2 R e v . 1 . 1
4508
4508S
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
S Y M P H O N Y
S p r e a d L a v a t o r y F a u c e t
with Speed Connect™ Drain
INSTALL SPOUT
INSTALL VALVE BODY
1
2
1
10
9
8
8a
10
9
11
3
Place RUBBER RING
(9)
into ADAPTER
(10)
.
8
5/16'' MIN.
7
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
Tubing Cutter
Fig.
A.
Fig.
B.
1
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only
on American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
11
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. Thread TEE BODY (4) to SPOUT SHANK (5) . Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, ...
9 INSTALL HANDLES CHECK DRAIN CONNECTIONS 10 11 12 13 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3) . Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3) . 1 HOT COLD 2 2 1 5 SERVI...
5 LIFT-KNOB Fig. C. STOPPER DOWN Speed Connect™ Drain Troubleshooting Guide 1 2 Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” ...
