American Standard 4098.100 - Manual

M44

© 2008 AS America Inc.

Revised 2/08

To Be Specified:

❏

Color:

❏

White

❏

Bone

❏

Linen

❏

Silver

❏

Fawn Beige

❏

Black

❏

Seat: American Standard #5324.019 “Rise and

Shine” (with easy to clean lift-off hinge system)
solid plastic closed front seat with cover.

❏

Seat: American Standard #5311.012 “Laurel”

molded closed front seat with cover.

❏

Alternate Seat:

❏

Supply with Stop:

* Flushmate III tank system by Flushmate

®

Div. of Sloan Valve Co

GLENWALL™ PRESSURE-ASSISTED

WALL-MOUNTED TOILET

VITREOUS CHINA

GLENWALL™ PRESSURE-ASSISTED TOILET

❏

2093.100

• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• Wall-mounted, back-outlet toilet
• Elongated bowl
• Fully-glazed 2" ballpass trapway
• 10" x 12" water surface area
• Pressure-assisted siphon jet action
• Side-mounted chrome trip lever
• Close-coupled flushometer tank*
• Speed Connect

®

tank/bowl coupling system

• Sanitary bar on bowl

❏

3402.016

Elongated bowl

❏

4098.100

Tank complete with coupling

components

Nominal Dimensions:

749 x 495 x 762 mm

(29-1/2" x 19-1/2" x 30")

Fixture only, seat and supply by others

Required working pressure range 25 psi - 80 psi

Alternate Configurations Available:

❏

4098.700

Tank and tank cover only

with tank cover locking device

❏

4098.800

Tank and tank cover only

with right hand trip lever

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• ASME A112.19.2 for Vitreous China Fixtures

NOTES:

WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-

FELT (WAX RING NOT RECOMMENDED)

SUGGEST 1/16" CLEARANCE BETWEEN FACE AT WALL AND BACK OF

BOWL.

CARRIER FITTING AS REQUIRED TO BE FIGURED AND FURNISHED BY

OTHERS.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED

SEPARATELY.

*

DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED.

FOR ADDITIONAL INFORMATION REFER TO INSTALLATION

INSTRUCTIONS SUPPLIED.

IMPORTANT

: Dimensions of fixtures are nominal and may vary within

the range of tolerances established by ANSI Standard A112.19.2. These

measurements are subject to change or cancellation. No responsibility is

assumed for use of superseded or voided pages.

14-3/4

(375mm)

9

(229mm)

29-1/2

(749mm)

9

(229mm)

18-1/2

(470mm)

C/L OF SEAT POST HOLES

5-1/2 (140mm CENTERS)

7-1/2

(191mm)

191mm

(7-1/2)

C/L OF WASTE

OUTLET

(4) 7/8

(22mm) DIA. HOLES

SUPPLY AS

REQUIRED

*

5/8

(16mm)

3-1/4

(83mm)

1-1/2

(38mm)

5-1/4

(133mm)

3-7/8

(98mm)

FINISHED WALL

FIN.

FLOOR

3-1/4

(83mm)

3/4 (19mm)

REF.

6

(152mm)

8-1/2

(216mm)

19-1/2

(495mm)

3/4

±

1/4

(19mm

±

6mm)

C/L

30

(762mm)

OR

32

(813mm)

14-1/2

(368mm)

OR

16-1/2

(419mm)

4-1/8

(105mm)

OR

6-1/8

(156mm)

When installed so top of seat is 432 to 483mm (17" to 19") from the
finished floor.

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USEABLE
BUILDING FACILITIES-CHECK LOCAL CODES.

BARRIER FREE