American Standard 3875-503 - Manual
American Standard 3875-503 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALL BLACK GASKET; INSTALL GRAY LOCKNUT
- Page 3 – MAKE WATER SUPPLY AND WASTE CONNECTIONS; NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED; HOT
- Page 4 – INSTALL HANDLE TRIM; SERVICE
- Page 5 – SpeedConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; “Locked”; Unlocked Mode
C O L O N Y S O F T
3875.403
3875.503
4
6
5
SLOT
MOUNTING
SURFACE
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT
(1)
and CABLE CONNECTOR
(2)
through center hole, making sure
the SEAL WASHER
(3)
is properly seated in SPOUT
(1)
.
Assemble RUBBER WASHER
(4)
, BRASS WASHER
(5)
and LOCKNUT
(6)
onto SPOUT
SHANK
(7)
from under side of sink . Make sure SPOUT
(1)
is centered in the mounting
hole and the
slot
in the BRASS WASHER
(5)
faces toward the rear of the sink.
Tighten LOCKNUT
(6)
firmly.
Fig. A.
Hand tighten LOCKNUT
(11)
to secure VALVE BODY
(12)
. Repeat above steps
for opposite VALVE BODY
(12A)
.
Install LOCKNUT
(11)
onto VALVE BODY
(12)
.
From under side of mounting surface, install VALVE BODY
(12)
through valve
mounting holes. Threads of VALVE BODY
(12)
should extent at least 5/16
of a inch above mounting surface top.
Fig. B.
Thread ESCUTCHEON
(10)
onto VALVE BODY
(12)
until snug against internal stop. If necessary, adjust
LOCKNUT
(11)
.
1
1A
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
S p r e a d L a v a t o r y F a u c e t
with
INSTALL SPOUT
INSTALL VALVE BODY
2
1
10
9
11
12
12a
10
9
12
11
3
Place RUBBER RING
(9)
into SCUTCHEON
(10)
.
5/16'' MIN.
7
SpeedConnect™ Drain
Adjustable Wrench
Screwdriver
Channel Locks
Required tools
Tubing Cutter
Congratulations on purchasing your American Standard faucet with
SpeedConnect drain, a feature found only on American Standard faucets.
SpeedConnect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the SpeedConnect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Fig. A.
Fig. B.
1
M 9 6 8 8 8 6
H
C
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INSTALL POP-UP DRAIN INSTALL BLACK GASKET 3 2 Install BLACK CONE GASKET (1) onto DRAIN BODY (2) from below. Note: The flat side of the BLACK CONE GASKET (1) must face down. 4 Drop DRAIN BODY (4) through sink drain hole. Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4) . Fig. B. Note...
WASTE OUTLET Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. Thread TEE BODY (4) to SPOUT SHANK (5) . Thread HOSE CONNECTOR (6, 6A) to VALVE CON...
CHECK DRAIN CONNECTIONS 10 11 12 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3) . Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3) . 1 HOT COLD 2 4 2 1 5 “P” TRAP WASTE OUTLET 3 ...
