American Standard 3821.631 Series - Manual
American Standard 3821.631 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – FERRULE; MAKE WATER SUPPLY CONNECTIONS; NOTE: FLEXIBLE SUPPLIES HAVE TO BE PURCHASED SEPARATELY
- Page 3 – TEST INSTALLED FAUCET; Turn on water supplies and check connections for leaks; AERATOR; Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.; SERVICE; and blot dry; CARE INSTRUCTIONS; H A N D L E
- Page 4 – MODEL NUMBERS; DIVERTER; SPOUT KIT
S I N G L E C O N T R O L K I T C H E N
F A U C E T W I T H C A S T S P O U T
I n s t a l l a t i o n
I n s t r u c t i o n s
M 9 6 8 1 8 8 E
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
3821.631 SERIES
3821.641 SERIES
3821.634 SERIES
3821.644 SERIES
1
2
3
4
5
6
7
8
A
B
9
CAUTION
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Turn off hot and cold water supplies before beginning.
P U T T Y
S P O U T B A S E
S P O U T B A S E
S I N K O R
M O U N T I N G
S U R F A C E
Assemble RUBBER WASHER (5), BRASS WASHER (6), and threaded LOCKNUT (7) onto SHANK (4) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Push O-RINGS (2) onto SPOUT SHANK. Make certain the O-RING (2) is properly seated in recess of DECORATIVE
FLANGE (10).
Insert SUPPLY TUBES (3) and SHANK (4) through mounting hole and seat DECORATIVE FLANGE (10) onto sink or
mounting surface.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1).
Apply a bead of putty to bottom edge of ESCUTCHEON (1).
Insert supply
TUBES (3) and SHANK (4) through hole of ESCUTCHEON (1) and mounting surface.
Make certain the O-RING (2)
is properly seated in recess of SPOUT BASE. Follow mounting instructions below to secure faucet to mounting surface.
(B)
Installation less ESCUTCHEON (1).
Remove ESCUTCHEON (1) , feed FAUCET TUBES (3) and SHANK (4) through
DECORATIVE FLANGE (10). Push FLANGE so the raised step fits into recess of SPOUT BASE.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
2
3
4
5
6
7
9
10
Regular Screwdriver
8
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M 9 6 8 1 8 8 E On model with separate spray, place the SPRAY HOLDER (1)into the appropriate mounting hole. Assemble the SPRAYHOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1)from below and tighten. Do not use putty. On model with spray through the ESCUTCHEON (3), placeSPRAY HOLDER (4) into the...
M 9 6 8 1 8 8 E 5 TEST INSTALLED FAUCET Move HANDLE down into "off" position and remove AERATOR. Turn on water supplies and check connections for leaks . Operate HANDLE up and down, left and right to flush waterlines thoroughly.For faucet with spray, direct SPRAY HEAD into sink andactivate S...
M 9 6 8 1 8 8 E MODEL NUMBERS S I N G L E C O N T R O L K I T C H E NF A U C E T W I T H C A S T S P O U T 042850-0070A DIVERTER 060366-0070A SPOUT SEAL KIT 912647-0070AO-RING SEAL 921877-0070ACAP RETAINER 060485-YYY0A ESCUTCHEON 060484-YYY0AESCUTCHEON WITHSPRAY HOLE M953040-YYY0A SPRAY HOLDER 02422...
