American Standard 3636.STTS - Manual
American Standard 3636.STTS – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
T O W N S Q U A R E
A C R Y L I C S H O W E R B A S E
M O D E L S 3 6 3 6 . S T T S , 3 8 3 8 . N E O T S , 4 8 3 4 . S T T S
I n s t a l l a t i o n
I n s t r u c t i o n s
7 5 2 7 6 9 - 1 0 0
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI Z124.2 1987.
Observe local plumbing and building codes.
NOTE: Read instructions completely before proceeding with installation.
For alcove (.STTS models) installation only: The opening
dimensions should be 1/8" larger than dimensions shown.
1
D
C
E
870mm
(34-1/4)
215mm
(8-7/16)
610mm
(24)
1219mm
(48)
4834.STTS
DRAIN
ASSEMBLY
Strainer
Drain
Body
Shower
Base
Silicone
Sealant
Rubber
Gasket
Fiber
Gasket
Locking
Nut
Rubber
Caulking
Gasket
Lift and lower base over center
of drain pipe and set into place
51x102 mm
(2x4) Stud Wall
Waterproof
Drywall
13mm (1/2")
minimum
Bedding Material Area
3 mm
(1/8)
127 mm (5)
51 mm (2)
PVC Pipe
3838.NEOTS
972mm
(38-1/4)
972mm
(38-1/4)
215mm
(8-7/16)
215mm
(8-7/16)
484mm
(19-1/16)
679mm
(26-3/4)
484mm
(19-1/16)
FRONT
Bedding
Material
No Bedding
Under
Apron
A
51 mm (2)
PVC Waste Pipe
127mmx127mm
(5x5) Opening
(See Product Chart for Drain Location)
C/L
C/L
3838 NEOTS
90
°
90
°
3636.STTS
914mm
(36)
457mm
(18)
914mm
(36)
215mm
(8-7/16)
FRONT
Insure the floor and
stud walls are square
and plumb. Provide a
5" x 5" (127mm x
127mm) opening in
the floor for the drain
(see Figs. A & B). The
drain plug accom-
modates a 2" (51mm)
PVC waste pipe. The
waste pipe should
extend above the
surface of the sub-
floor 3/8"
±
1/16".
Note: Variations in
levelness of subfloor
may require
adjustment of waste
pipe height. See
product drawings on
this page for the
specified drain
locations.
Before installing drain
into the shower base,
remove strainer (see Fig.
C). This will be installed
after shower base is in
its final position. Install
the drain to the shower
base as shown in Fig. D.
Use silicone sealant
between drain body and
shower base.
After leveling base on subfloor, use base and mark
studs. This will be the installed height of shower base.
Mix the low-shrink bedding material (grout, mortar,
plaster, etc.). Concrete is not recommended. Apply
enough bedding material to support the entire bottom of
the shower base. The bedding material must not be
used under the apron (front edge).
B
3636.STTS, 4834.STTS
90
°
90
°
51 mm (2)
PVC Waste Pipe
127mmx127mm
(5x5) Opening
C/L
(See Product Chart for Drain Location)
2
3
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
