American Standard 3475.500 - Manual
American Standard 3475.500 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TIGHTEN LOCKNUT; FLANGE GASKET
- Page 4 – OUTLINE OF BIDET
- Page 5 – SpeedConnectTM Drain; Troubleshooting Guide; CABLE ADJUSTMENT PROCEDURE; If Stopper does not raise up fully or sink drains too slowly:; STOPPER REMOVAL PROCEDURE
- Page 6 – STOPPER INSTALLATION PROCEDURE; “Locked”; Locked Mode
3475.300
3475.500
COLONY/COLONY SOFT
3
5
4
4
Certified to comply with ANSI A112.18.1
Installation
Instr uctions
B i d e t F a u c e t a n d Tr a n s f e r Va l v e
with SpeedConnect™ Drain
Congratulations on purchasing your American
Standard faucet with Speed Connect drain, a
feature found only on American Standard faucets.
*Your new American Standard faucet is designed to work only with the SpeedConnect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
M 9 6 8 7 9 5 R e v. 1 . 1
Turn off hot and cold water
supplies before beginning.
CAUTION
1
BIDET FAUCET INSTALLATION
Replace UPPER GASKET
(8)
and WASHER
(7)
and
ESCUTCHEON (6) until it locks against internal stop.
Position the side threaded outlet rearward and
secure MOUNTING NUT
(11)
.
Remove ESCUTCHEON
(6)
, WASHER
(7)
and
UPPER GASKET
(8)
from TRANSFER VALVE
(9).
Insert TRANSFER VALVE
(9)
into the center forward
hole of BIDET.
COLD
HOT
BIDET
LEDGE
10
4
3a
3
8
9
1
5
2
6
SPRAY INSTALLATION
2
Assemble SPRAY BODY
(1)
to BIDET. Using putty, seal underside
of SPRAY BODY FLANGE
(2)
and secure with NUT
(3)
.
Thread SPRAY CAP
(9)
onto SPRAY BODY
(1)
.
Thread SPRAY HOSE
(4)
with SEAL WASHER
(5)
to SPRAY BODY
(1)
.
Connect other end of HOSE
(4)
with SEAL WASHER
(6)
to side outlet
NIPPLE
(7)
of the TRANSFER VALVE
(8)
.
PUTTY
6
2
7
8
1
9
Tighten LOCKNUTS
(1)
with WRENCH
(5)
(supplied)
to secure VALVE BODIES
(3, 3a)
.
Install LOCKNUT
(1)
and RUBBER WASHER
(2)
onto VALVE BODIES
(3, 3a)
. From
under side of mounting surface, install VALVE BODY
(3, 3a)
through valve mounting
holes. Threads of VALVE BODY
(3, 3a)
should extent at least 5/16 of a inch above
mounting surface top.
Fig. A.
Thread ESCUTCHEON
(4)
onto VALVE BODIES
(3, 3a)
until snug against internal stop. If necessary, adjust LOCKNUT
(1)
.
Place RUBBER RING
(10)
into ESCUTCHEON
(4)
.
MOUNTING
SURFACE
4
10
2
1
3, 3a
5/16''
MIN.
Fig. A.
11
Adjustable Wrench
Screwdriver
Channel Locks
Required tools
Tubing Cutter
Phillips Screwdriver
Plumbers' Putty or
Caulking
7
1
R o u g h i n g - i n
D i m e n s i o n s
BIDET OUTLINE
IS SYMBOLIC
FINISHED
FLOOR
FINISHED
WALL
1-1/4 O.D. TAILPIECE
DOUCHE
SPRAY
2-1/8
DIA.
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
1-1/4
MAX.
1-3/16
DIA.
2-1/4
DIA.
(C)
(H)
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
8 TO 12
SpeedConnect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
M 9 6 8 7 9 5 R e v. 1 . 1 2 POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. DRAIN BODY 7 3 5 4 TIGHTEN LOCKNUT 1 REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise ...
INSTALL HANDLES (Lever) INSTALL HANDLES (Acrylic) CHECK DRAIN CONNECTIONS 12 11 13 14 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Operate both HANDLES (1) to flush water lines thoroughly. Rotate TRANSFER VALVE (5) from rim ...
M 9 6 8 7 9 5 R e v . 1 . 1 SpeedConnect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the ill...
