American Standard 2808.222 - Manual
American Standard 2808.222 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – DOWN
- Page 3 – MAKE WATER SUPPLY AND WASTE CONNECTIONS; NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED; HOT
- Page 4 – To change direction of handle rotation, proceed as follows:
2808.222
2908.222
T M
4
6
5
SLOT
MOUNTING
SURFACE
Insert SPOUT
(1)
and CABLE CONNECTOR
(2)
through center hole, making sure
the SEAL WASHER
(3)
is properly seated in SPOUT
(1)
.
Assemble RUBBER WASHER
(4)
, BRASS WASHER
(5)
and LOCKNUT
(6)
onto SPOUT
SHANK
(7)
from under side of sink . Make sure SPOUT
(1)
is centered in the mounting
hole and the slot in the BRASS WASHER
(5)
faces toward the rear of the sink.
Tighten LOCKNUT
(6)
firmly.
Fig. A.
Hand tighten LOCKNUT
(11)
to secure VALVE BODY
(12)
.
Repeat above steps for opposite VALVE BODY
(12A)
.
Install LOCKNUT
(11)
onto VALVE BODY
(12)
.
From under side of mounting surface, install VALVE BODY
(12)
through valve
mounting holes. Threads of VALVE BODY
(12)
should extent at least 5/16
of a inch above mounting surface top.
Fig. B.
Important:
Thread ESCUTCHEON
(10)
onto VALVE BODY
(12)
until snug against
internal stop. This is key to the installation. If not done, the faucet handles won’t
work correctly. If necessary, adjust LOCKNUT
(11)
.
1
1A
Certified to comply with ANSI A112.18.1
I n s t a l l a t i o n
I n s t r u c t i o n s
INSTALL SPOUT
INSTALL VALVE BODY
2
10
9
11
12
12a
10
9
12
11
3
Place RUBBER RING
(9)
into ESCUTCHEON
(10)
.
5/16'' MIN.
7
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
Tubing Cutter
Fig.
B.
1
U S 6 0 3 8 5 R e v. 1 . 2
W i d e s p r e a d L a v a t o r y F a u c e t w i t h t h e
Speed Connect™ Drain
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
1
Fig.
A.
1
2808 SERIES
Congratulations on purchasing your American Standard faucet with
the Speed Connect Drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
Turn off water at
main supply.
CAUTION
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INSTALL POP-UP DRAIN INSTALL BLACK GASKET 3 2 Install BLACK CONE GASKET (1) onto DRAIN BODY (2) from below. Note: The flat side of the BLACK CONE GASKET (1) must face down. 4 Drop DRAIN BODY (4) through sink drain hole. Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4) . Fig. B. Note...
Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. Thread TEE BODY (4) to SPOUT SHANK (5) . Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, ...
CHECK DRAIN CONNECTIONS 10 11 12 TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3) . Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3) . 1 HOT COLD 2 4 2 1 5 “P” TRAP WASTE OUTLET 3 ...
