American Standard 2722.202 LHO - Manual

All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.
© AS America, Inc. 2009

HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS

Local building codes vary by location. Observe all local plumbing and building codes.
Your new bath is shipped to you after careful inspection. All you need to finish the installation are your selected fittings.
To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

• Level

• Square

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

• Nails

• Plumber’s Putty

• Silicone Sealant

• 1 x 3 or 2 x 4 Stringers

• Drop Cloth

• Mortar Mix or Grout

754049-100 Rev. J

754049-100 Rev. J

754049-100 Rev. J

754049-100 Rev. J

POST INSTALLATION CLEAN-UP

Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.

Do not use wire brushes or any other metal implement on bath surface.

Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or

stains may be removed using granular Spic and Span® mixed with water.

Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.

FEATURES of YOUR NEW AMERICAN STANDARD ACRYLIC BATHTUB

Your new acrylic bathtub has been molded in the newest plumbing fixture material available today. Acrylics are tough

durable finishes that are simple and easy to care for.

The colors have been formulated to match other American-Standard fixtures and enhance your choice of bathroom

decorations. The high gloss surface is resistant to impact and chemicals and will retain its lasting luster with proper care

and maintenance.

AFTERCARE and CLEANING

• Always fill the tub with temperate water. Excessively hot water may cause surface damage

• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.

• Clean after use with a mild liquid household detergent cleaner. Abrasive cleaners such as Lestoil, Lysol Disinfectant

(spray or concentrate), or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner, or

cleaning products in aerosol cans should not be used.

HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.

• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits, or other surface blemishes.

• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses its sheen,

dulled areas can be restored by rubbing with a white polishing compound and waxing with a "liquid wax."

•

Do not wax areas where you walk or stand.

• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into contact with the

surface.

• Clean the surrounding surface immediately after using caustic drain cleaners.

• Burning cigarettes will damage the surface.

• Should damage to the fixture occur, repairs can be made quickly and easily. Your distributor or builder can provide details.

4

3

2

AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this bathing pool – American

Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser.
To activate this limited warranty, the purchaser must go online to our website at www.americanstandard-us.com/warranty to register their bathing pool within thirty

(30) days of purchase.
In no event will American Standard be liable for the cost of repair or replacement of any installation materials including but not limited to tile, marble, etc.
This limited warranty does not apply to Commercial Installations. The warranty for Commercial Installations is three (3) years.

This limited warranty DOES NOT COVER the following:
1. Defect or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenance and cleaning as directed in the

Installation Instruction Manual and use of other than genuine American Standard replacement parts, in all cases whether caused by a plumbing contractor,

service company, the owner or any other person.

2. Deterioration through normal wear and tear and the expense of normal maintenance.

3. Commercial application.

4. Options and accessories. American Standard's limited warranty on these items is

one year for parts only and excludes labor.

This one year limited

warranty covers accessories manufactured by American Standard (e.g. aprons, drains, grab bars, heaters, trim kits) against defects of material or

workmanship. Warranty coverage begins on the date the accessory was originally purchased by the owner.

5. Shipping cost for returning products for repairs or replacement under the limited warranty and labor or other cost incurred in connection with product removal

or installation under this limited warranty.

6. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY EXPRESSLY DISCLAIMED, OR THE EXTENSION

BEYOND THE DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS

FOR AN INTENDED PURPOSE. (Some jurisdictions do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental

or consequential damages, so these limitations and exclusions may not apply to you.)

7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly, distributors, retailers, dealers, installation

contractors and users of plumbing products should determine whether there are any code restrictions on the installation or use of a specific product.)

This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case

this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a

service request (including a description of the product model and of the defect) be sent to the following address:

In the United States:

American Standard Brands

P.O. Box 659

West Caldwell, NJ 07007

Attention: Customer Care

In Canada:

AS Canada, ULC

2480 Stanfield Road

Missassauga, Ontario

Canada L4Y 1S2

In Mexico:

Customer Service Manager

AS Maquila, S.A. de C.V.

Via Morelos #330

Col. Santa Clara

Ecatepec 55540 Edo. Mexico

For residents of the United States, warranty

information may be obtained by calling the

following toll free number (800) 442-1902

AS America, Inc. Limited Lifetime Warranty for Rope Twist™ Bathing Pools

1. WHEN INSTALLING THE MATCHING ROPE TWIST BATH WALLS (MODEL 5030.LBW),
ADDITIONAL STUDS MAY BE REQUIRED. REFER TO THOSE INSTALLATION INSTRUCTIONS
PRIOR TO INSTALLING TUB.

2. ROPE TWIST SHOWER WALLS ARE TO BE INSTALLED OVER STUD WALLS.

3. BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLAION.

4. THIS BATH IS NOT SELF-SUPPORTING AND MUST BE SUPPORTED ALONG ITS ENTIRE
BOTTOM WITH MORTAR OR GROUT. STRINGERS WILL HELP LEVEL TUB, BUT WILL NOT
PROVIDE ADEQUATE SUPPORT.

5. TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE BATH.

6 0 x 3 2 x 1 7 I n .

( 1 5 2 4 x 8 1 3 x 4 3 2 m m )

60 Lbs. (27 Kg)

393 Lbs.(179 Kg)

40 Gal. (151 L)

22 x 44 In. (559 x 1118mm)

25.5 X 53 In.(648 x 1346mm)

10 In. (254mm)

29 Lbs./Sq.Ft. (195 Kgs/Sq.m)

15.3
27

GENERAL SPECIFICATIONS FOR 2722 BATHING POOL

INSTALLED SIZE

WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)

ROPE TWIST™ BATHING POOL

Installation Instructions

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure

that your installation proceeds smoothly--please read these instructions carefully before you begin.

BEFORE YOU BEGIN....

GENERAL INSTALLATION INFORMATION ....

TOOLS:

TOOLS & MATERIALS REQUIRED....

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

MATERIALS:

HOTLINE FOR HELP

FOR TOLL FREE INFORMATION AND ANSWERS TO YOUR QUESTIONS, CALL:

1 (800) 442-1902, in Canada call 1 (800) 387-0369.

Weekdays 8:00 a.m. to 4:00 p.m. Eastern time.

MODELS: 2722.102 RHO

2722.202 LHO

USED WITH BATH WALLS: 5030.LBW

ROUGH-IN INFORMATION:

1-1/2 N.P.T. THREADS

1-1/2 O.D. TAILPIECE

16-3/4"

(425mm)

2"
(51mm)

4-5/8"

(117mm)

ROUGH
FLOOR

17"

(432mm)

1"

(25mm)

FINISHED
WALL

SEE

NOTE

3-1/2"
(89mm)

32"
(813mm)

60"

(1524mm)

3/4"

(19mm)

70mm
(2-3/4)

9-3/8"

(238mm)

FINISHED

WALL

C/L OF
DRAIN

229mm x 305mm
(9 x 12)
FLOOR
CUTOUT

15-1/8"

(385mm)

4-1/2"

(114mm)

25mm
(1)

BATH SUPPORT

MATERIAL

TOP OF

DECK

1

INSTALLATION AND FRAMING INSTRUCTIONS:

A.)

Locate studs as required. Ensure roughing-in dimensions are proper, plumb, and square. It is strongly recommended that an additional

opening be provided for access to the drain components.

B.)

As shown in ILL. 2, mark the position of the underside of the deck by tracing a line onto the studs at the height indicated, using a level or

other suitable straight edge.

C.)

With the top of the stringer touching the traced line, attach the stringer to the studs.

D.)

Install drain components to the bath following the manufacturer's instructions. See the roughing-in drawing for suggested opening size and

location dimensions.

2

A.) THIS BATH MUST BE SUPPORTED ALONG IT'S ENTIRE BOTTOM.

We recommend the use of mortar as bedding material (sand is not

recommended). Apply enough bedding to support the complete bottom of the bath. After the bedding has been poured, and before it sets,
position the bath within the recess until the rim is leveled against the leveling stringers (see "Typical Recess Installation") shown below. The rim
of the bath

MUST NOT

support weight. Allow the bedding material to completely harden before applying weight to the rim or bottom of the bath.

C.)

Any finish material such as tile or wallboard must be self-supporting if it contacts the deck of the bath.

B.)

Check level front to back and side to side, shim as necessary. To secure the tub to wood studs, use drywall screws with flatwashers or

roofing nails immediately above the flange of the bath. To secure the tub to steel studs, use 4" drywall screws and flatwashers.

16-3/4

(425mm)

TYPICAL RECESS INSTALLATION

34 Typ.

(864mm)

60-3/16

(1529mm)

3 2

( 8 1

3 m

m )

T U

B W

I D T

H

L E V E L I N G
S T R I N G E R S

Flooring will be butted against the bottom of the tub apron, also holding the tub in place.

DRAIN CONNECTION

Using recommended drain opening, connect bath drain to waste line. Tighten all drain joints securely.

3

SPIC AND SPAN® IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE

Illustration 1

Illustration 2

Each alcove

stud must

be plumb

and square.

3 0

( 7 6

2 m m

)

SUGGESTED BATH

INSTALLATION METHOD

SECURE THE BATH TO THE STUDS AS SHOWN

FOR WOOD OR STEEL STUD CONSTRUCTION.

TYPICAL FLANGE MOUNTING DETAIL

STUD

WATERPROOF DRYWALL
OR CEMENT BOARD

WATERPROOF DRYWALL

OR CEMENT BOARD

TILE

SEALANT

TUB

ROOFING NAIL

1 x 3 (25 x 76mm) WOOD

STRINGER FULL LENGTH

1 x 3 (25 x 76mm) WOOD

STRINGER FULL LENGTH

STEEL

STUD

WASHER

TILE

SEALANT

TUB

4" (102mm)

DRYWALL

SCREW

WOOD

STUDS

STEEL

STUDS