American Standard 2580 - Manual
American Standard 2580 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – FERRULE; FINISH DRAIN INSTALLATION; Position BIDET fixture and secure to floor.; TEST INSTALLED FITTING
- Page 4 – BIDET FITTING; MODEL NUMBER
- Page 5 – R o u g h i n g - i n D i m e n s i o n s; CAUTION; MOUNTING BIDET FAUCET; *Supplied with Fitting; Required Tools; Tubing Cutter; COLD; quality for over 100 years.; DRAIN INSTALLATION
I n s t a l l a t i o n
I n s t r u c t i o n s
M 9 6 8 2 9 2
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
R o u g h i n g - i n D i m e n s i o n s
(C)
(H)
8 TO 12
Turn off hot and cold water
supplies before beginning.
CAUTION
1
DRAIN INSTALLATION
2
MOUNTING BIDET FAUCET
STOPPER
Assemble O-RING (1), WASHER (2), PIVOT
ROD (3) and NUT (4) to DRAIN BODY (5).
Concave side of cup WASHER (2) is toward
ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET
and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
BIDET
PUTTY
CLIP
9
3
1
4
11
6
5
8
7
2
10
2580
BIDET FITTING
*Wrench
*Supplied with Fitting
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Phillips Screwdriver
Required Tools
Tubing Cutter
by
C O L L E C T I O N
™
T H E
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside
holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and
thread DECK ADAPTER (4) onto VALVE BODIE (2)
until it locks against the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Replace UPPER GASKET (7), and ESCUTCHEON (5)
until it locks against the internal stop. Position the
side threaded outlet rearward and secure
MOUNTING NUT (9).
COLD
HOT
BIDET
LEDGE
3
4
2
7
8
1
9
5
Remove ESCUTCHEON (5), WASHER (10) and
UPPER GASKET (7) from TRANSFER VALVE (8) and
insert into the center forward hole of BIDET.
10
BIDET OUTLINE
IS SYMBOLIC
FINISHED
FLOOR
FINISHED
WALL
1-1/4 O.D. TAILPIECE
DOUCHE
SPRAY
2-1/8
DIA.
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
1-3/8
MAX.
1-3/16
DIA.
2-1/4
DIA.
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds
smoothly--please read these instructions carefully before you begin.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
SERVICE To change direction of handlerotation, proceedas follows: Turn valve to OFF position.Remove HANDLE andADAPTER if present.Remove SPRING CLIP (1).Lift STOP WASHER (2),turn 90 ° and replace. Replace SPRING CLIP (1).Replace HANDLE ASSEMBLY. 90 ° WATER SUPPLY CONNECTIONS 7 Cold Connect water supp...
M 9 6 8 2 9 2 CHROMESATIN 002295 Replace the "YYY" withappropriate finish code BIDET FITTING MODEL NUMBER 2581 by C O L L E C T I O N ™ T H E 024220-0070ACOUPLING NUT M962164-0070ALIFT ROD M961656-YYY0A LIFT ROD GUIDE 060463-0070A ADAPTER KIT 028704-0070A TEE AND HOSE KIT (INCLUDING SEALS) 9...
I n s t a l l a t i o n I n s t r u c t i o n s M 9 6 8 2 9 3 Certified to comply with ASME A112.18.1MU.S. Patent No. 5,819,789 R o u g h i n g - i n D i m e n s i o n s BIDET OUTLINEIS SYMBOLIC FINISHEDFLOOR FINISHED WALL 1-1/4 O.D. TAILPIECE ADJ. 1-1/4 TO 2-1/4 3-7/8 5-1/2 1-3/8 DIA. 7/8 DIA. DIVE...
