American Standard 2555.034 - Manual

Certified to comply with ANSI A112.18.1

M 9 6 8 2 3 2 C

1

18" TOWEL BAR, 24" TOWEL BAR, 24" TOWEL BAR W/GLASS SHELF AND
TOILET TISSUE HOLDER MOUNTING & INSTALLATION

The 18" TOWEL BAR (1), 24" TOWEL BAR (2), 24" TOWEL BAR W/GLASS SHELF (3) and TOILET TISSUE HOLDER (11) work best
if secured to a wall stud or cross brace within the wall, using the SCREWS (4) supplied.

If the 18" TOWEL BAR (1), 24" TOWEL BAR (2), 24" TOWEL BAR W/GLASS SHELF (3) and TOILET TISSUE HOLDER (11)
are to be installed on a tile or plaster wall the ANCHORS (8) and SCREWS (4) should be used.

SET
SCREW

A C C E S S O R I E S

T O W N S Q U A R E

I n s t a l l a t i o n

I n s t r u c t i o n s

2555.018
2555.024
2555.034
2555.061

Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these
instructions carefully before you begin.

INSTALL 18" TOWEL BAR, 24" TOWEL BAR, 24" TOWEL BAR W/ GLASS SHELF AND TOILET TISSUE HOLDER

2

12

14

15

14

12

3

18

17

16

2 11

1

18"TOWEL BAR

24"TOWEL BAR

24"TOWEL BAR WITH GLASS SHELF

TOILET TISSUE HOLDER

19

Regular Screwdriver

Recommended Tools

Phillips Screwdriver

Drill

10'

Tape Measure

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.

Secure MOUNTING PLATES (5) to wall with SCREWS (4).

For installations on tiled walls,

If TILE ANCHORS (8) and SCREWS (4) are used for securing MOUNTING PLATE (5), then

drill two 1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (8) flush with face of the finished wall.

Determine desired height and location (optional) and mark a center line. For the 24" TOWEL BAR (2) and 24" TOWEL BAR W/GLASS
SHELF mark a centerline 24" horizontally from the first location. For the 18" TOWEL BAR (1) mark a centerline 18" from the first location.
For the TOILET TISSUE HOLDER (11) mark a centerline 7" from the first location. Using the MOUNTING PLATE (5) as a template mark the
two spots for the mounting holes. Repeat for the other MOUNTING PLATE (5). If MOUNTING PLATE (5) is secured to a stud or cross
brace drill small pilot holes for SCREWS (4).

For installations on drywall,

use DRYWALL ANCHOR (6) and SCREWS (4) for securing MOUNTING PLATES (5) to wall. Place #2 Phillips

screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with
the wall. Place MOUNTING PLATES (5) over DRYWALL ANCHORS

(6) and insert screws provided with #2 Phillips screwdriver. See

illustration below. Secure MOUNTING PLATES (5) to wall with SCREWS (4).

4

5

FINISHED WALL

USE MOUNTING BRACKET (5)
AS TEMPLATE

5

8

6

4

8

Install the 18" TOWEL BAR (1), 24" TOWEL BAR (2), 24" TOWEL BAR W/ GLASS SHELF (3) into WALL ESCUTCHEON (7).

Tighten SET SCREW (9) using 2-1/2mm HEX KEY (10) supplied to secure accessory assembly to WALL ESCUTCHEON (7).

Place ESCUTCHEON (7) onto MOUNTING BRACKET (5), and secure with ATTACHMENT SCREW (20).

For the 24" TOWEL BAR W/ GLASS SHELF (3), Install TOWEL BAR (16) into bottom of HANGER ROD POSTS (17). Align SET SCREW (19)
in back of LEFT HANGER ROD POST (17) with hole in TOWEL BAR (16). Tighten SET SCREW (19) to restrict rotation of TOWEL BAR (16).
Install the SQUARE WASHER (12), WASHER (14), GLASS SHELF (15), WASHER (14) and SQUARE WASHER (12) onto HANGER ROD
POST (17). Install and tighten SCREWS (18). See illustration.

10

9

7

20