American Standard 2388 - Manual
American Standard 2388 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALL TOILET; DO NOT OVERTIGHTEN NUTS; INSTALL TANK; DO NOT OVERTIGHTEN NUTS MORE
- Page 3 – REPAIR PARTS LIST; DESCRIPTION; CARE AND CLEANING; Diagram 1
- Page 4 – INSTRUCTIONS TO INSTALL TOILET SEAT; Insert bolts in hinges.; Use a screwdriver to tighten bolt.; For troubleshooting information please contact:; it is a signal you are wasting water because:; NOTE; Pictures are representative and may not; TOILET SEAT CARE AND CLEANING
- Page 5 – does not apply; This warranty; shall be void; other costs of removal or installation,; TROUBLESHOOTING GUIDE; PROBLEM; In the United States:
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel and slide
into place parallel to wall.
SAVE FOR FUTURE USE
3
2
CLOSET FLANGE
CLOSET BOLTS
7 3 0 1 1 8 6 - 1 0 0 R e v . B
A
FINISHED WALL
FINISHED
FLOOR
SUPPLY
AS
REQ'D.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a I n c . 2 0 0 8
NOTE:
Pictures may not exactly define contour of china and components.
ROUGHING-IN DIMENSIONS:
NOTE:
Distance from wall to closet flange centerline must
be as listed below:
A = 12" (305mm)
A
WAX RING
SEALANT
5
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP"
must
face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations
may require professional help.) Also be sure your installation conforms to local codes.
!
RENAISSANCE EL TOTAL TOILET 2446
COLONY 2388 2399 2359
INSTALLATION
INSTRUCTIONS
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
7 3 0 1 1 8 6 - 1 0 0 R e v . B 6 8 7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Install caps...
7 3 0 1 1 8 6 - 1 0 0 R e v . B 10 11 ADJUSTMENTS a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. See Step 11 for water level adjustment method. b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the c...
7 3 0 1 1 8 6 - 1 0 0 R e v . B - 4 - 12a 12d 12f 12e 12c INSTRUCTIONS TO INSTALL TOILET SEAT Place seat on bowl. Be careful to center hinge over holes in bowl. Insert bolts in hinges. Attach the nut from below. Use a screwdriver to tighten bolt. Close the hinge covers. 12b 13 • Make sure water supp...
