American Standard 2384 - Manual
American Standard 2384 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALL TOILET; DO NOT OVERTIGHTEN NUTS; INSTALL TANK; DO NOT OVERTIGHTEN NUTS MORE
- Page 3 – CARE AND CLEANING; tank. This damage can cause leakage and property damage.; Diagram 1; REPAIR PARTS LIST; Complete
- Page 4 – For troubleshooting information please contact:; TROUBLESHOOTING; does not apply; any damage caused by the use of in-tank cleaners.; nor shall; In the United States:; TROUBLESHOOTING GUIDE; PROBLEM
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level
before
new toilet is installed!
SAVE FOR FUTURE USE
7 3 0 9 2 8 - 1 0 0 R e v . F
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 8
NOTE:
Pictures may not exactly define contour of china and components.
CADET
®
3 - 1.6 GPF TWO-PIECE TOILET
Models 2383 / 2384 / 2386 / 2447 / 2431 / 2880 / 3305
CADET
®
3 FloWise™ - 1.28 GPF TWO-PIECE TOILET
Models 2829 / 2832 / 2835 / 2838 / 2880 / 3305
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional
help.) Also be sure your installation conforms to local codes.
2
CLOSET
FLANGE
CLOSET
BOLTS
A
FINISHED WALL
FINISHED
FLOOR
SUPPLY
AS
REQ'D.
A
WAX RING
SEALANT
5
4
3
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly
around waste flange (horn), with tapered
end of ring facing toilet. Apply a thin bead
of sealant around toilet base.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP"
must
face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
ROUGHING-IN DIMENSIONS:
NOTE:
Distance from wall to closet flange centerline must be as listed on chart:
INSTALL CLOSET BOLTS
Install closet bolts in flange
channel, turn 90°, and slide
into place 6" (152mm) apart
and parallel to wall.
!
MODELS
DIMENSION “A”
10"
ROUGHS
12"
ROUGHS
14"
ROUGHS
254mm (10)
305mm (12)
356mm (14)
2383.012
2386.012
2384.012
3305.000
2431.012
2447.000
2880.000
2829.128
2832.128
2835.128
2838.128
2447.128
2880.128
2383.010 2384.010
2386.010
2383.014 2384.014
2386.014
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
7 3 0 9 2 8 - 1 0 0 R e v . F RUBBER GASKET TANK MTG.BOLTS PRE-INSTALLED 6 8 7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUT...
7 3 0 9 2 8 - 1 0 0 R e v . F 10 11 ADJUSTMENTS a. Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup. See Step 11 for water level adjustment method b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead...
7 3 0 9 2 8 - 1 0 0 R e v . F 13 - 4 - • Make sure water supply is off. Remove valve TOP by lifting arm and rotating top and arm 1/8 turn counterclockwise, pressing down slightly on cap. IMPORTANT: Always clear sand and rust from system. • While holding a container over the uncapped VALVE to prevent...
