American Standard 2373.901 - Manual
American Standard 2373.901 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CAUTION; SPOUT ASSEMBLY; NOTE; Note: For product with Hand; VALVE ASSEMBLY; MOUNTING
- Page 3 – UNTHREAD; TOP
- Page 4 – To remove handles, reverse steps in section 4.; TEST INSTALLED FAUCET; Operate both handles and flush water lines thoroughly.; The flow rate of this Tub Filler exceeds 20 gallons/minute; EverCleanTM Finish Care Instructions
*Wrench
Certified to comply with ANSI A112.18.1M
Required Tools
*Supplied with Fitting
*Hex key
Adjustable Wrench
Channel Locks
Flat Blade Screwdriver
D E C K - M O U N T B AT H F I L L E R
ENFIELD
MOUNTING
SURFACE
ADJ. 6-1/2 TO 12
8"
3-3/4"
5-3/16"
1-1/2 MAX.
1-1/4
MAX.
1-3/16 DIA.
3
(
H
)
(
C
)
1-1/8 DIA.
8-3/16
12 MAX
2-1/16
DIA.
1-1/16 DIA.
3/4-14 MALE
N.P.T. INLETS
2-7/8"
LEVER
HANDLE
CROSS
HANDLE
2-1/4
DIA.
2-7/8
DIA.
M 9 6 8 2 8 8 R e v . 1 . 1
2373.900
2373.920
2373.901
2373.921
Installation
Instructions
ROUGHING-IN DIMENSIONS
w i t h
EverClean™ Finish
Congratulations on purchasing your American
Standard faucet with EverClean finish found
only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
IMPORTANT NOTICE TO INSTALLER!
Please check with local Code Authority for the installation requirements of this product. Some codes require an
additional temperature mixing valve to limit the maximum hot water temperature
and vacuum breaker
(for products with hand spray)
to be installed with this product.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
SPOUT BASERECESS Turn off hot and cold watersupplies before beginning. CAUTION 1 2 Assemble RUBBER WASHER (5) and LOCKNUT (6) onto SPOUTSHANK (1). Align SPOUT ASSEMBLY and from underside of ledgesecure SPOUT ASSEMBLY into position with LOCKNUT (6). SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY 3 1 4 ...
4 INSTALL HANDLES Push ADAPTER (1) on VALVE STEM (2), so that the hole of theADAPTER (1) without a spline is facing up. See figure "A". TightenSTEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) or CROSSHANDLE ASSEMBLY (5) by adjusting male teeth on ADAPT...
9 Before the bathroom is completely finished, you may want to remove spout, hand shower, and handles. To remove handles, reverse steps in section 4. To remove SPOUT (1), proceed as follows: Lift TRANSFER ROD (8) and unscrew KNOB (2). Remove PLUG BUTTON (3) and remove SET SCREW (4) using 5mm hexwrenc...
